User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

The WLF-90 main control lever is suitable for single and dual main engine control in the propulsion systems of medium and small-sized ships. The product has the following characteristics: -The product is made of all-aluminum alloy, with a black powder-coated handle. The scale is backilluminated for indication. The control damping and gear feedback feel are adjustable. It meets the electromagnetic compatibility and vibration requirements of the IEC60945 standard and features a compact design, sturdy structure and high precision., as shown in Table 1.1. Basic options (Note: Option 1 is the default...

According to the position of the handle, the product is divided into two main push 90D, left main push 90L and right main push 90R, as shown in Figure 1.2. When selecting, we should inform our sales staff according to personal needs to avoid unnecessary economic losses!

1.5 Product wiring diagram Each side of the handle provides a separate PCB board, although this is a multi-in-one circuit board, but the production has been fixed in accordance with the requirements of the order to solidify the function (including output signal and dimming signal), each side contains 16 terminals, where P1-P3 is the potentiometer output signal (if any), P4~P5 is the output of 4~20mA (if any), P6 to P7 are commissioning ports, P11 to P12 are dimming ports, and P13 to P14 are DC24V power ports.

1. The main body of the handle is made of aluminum alloy, the surface is made of black spray plastic, the main shaft is made of stainless steel, and the interior is driven by copper gear; 2. The scale range is 100-0-100, the background color is green before and red after, the scale line and digital white, the backlight is always on, and the brightness can be adjusted through an external dimmer; 3. Constant operating torque, adjustable rotating torque and caton point feel; 4. Resistance tolerance of potentiometer ±10%, independent linear tolerance 1.0%; 5. Output mode: direct potentiometer linear...

2. Rotation range: The rotation range of the handle can be ±60°, 0-60°, or -15-60°. The default is ±60°, as shown in Figure 2.3, 3. Gear feedback: The handle can provide stuck feedback at a specific gear, such as in the middle zero position or any other gear, and the default output is only stuck feedback at zero position. 4. Output signal: The handle can provide a variety of optional output signals for the control system, including the direct output of the potentiometer, 4~20mA, and can also provide passive switch contacts. Please refer to wiring diagram 1.5 for the direct output type of potentiometer...

In general, the corresponding relationship of output signals is as follows: scale -100% corresponds to 4mA output, scale 0 corresponds to 12mA output, and scale +100% corresponds to 20mA output, as shown in Figure 2.5. For the need to collect the handle ahead, stopping, reversing signals, you can also choose the corresponding module to achieve passive switch contact output, single push or double push handle can be configured, the module can be configured according to the need to configure 1~3 limit switches (brand: Japan Omron), output normally open or normally closed signals. The size of the...

For 0-24V dimming signals, the dimming signal is the darkest at OV and the brightest at 24V. Note that the dimming signal and the power signal cannot be shared, otherwise the handle signal output will be affected, resulting in failure to work normally. The connection diagram is shown in Figure 2.7: Please consult our sales staff to determine the selection of PWM dimming interface signal. 4 to 20mA output wiring diagram Each handle provides 16 terminal connections. Terminal 1/2/3 output handle potentiometer signal is used to calculate the current Angle; Terminal 10/11/12 connected to dimmer potentiometer,...

Spring washers, flat washers and nuts 2. Place the handle vertically in the opening of the mounting plate as shown in the lower right corner of Figure 3.2, and align the screw with the hole B. Rotate or tilt the handle into the hole when it meets the protruding part.

4. After the handle is installed on the mounting plate, Figure 2.5 shows the electrical cables. After the wiring is completed, it should be confirmed that the external wiring is firm and reliable. 5. Check the external cables, which should be connected normally; The backlight should emit light normally; Push the handle lever, the switch can complete the normal on-off action. After commissioning, disconnect the power supply.

1. The initial position of the hand on the handle is in the middle (0 scale). At this time, the resistance value corresponding to the advance direction of the potentiometer (terminals 1 and 2) is 2.5KQ± 10%. 2. Switch on the power supply, connect the cables as shown in Figure 1.5, push the handle rod, and the resistance reading between terminals 1 and 2 is the output value of continuous linear change in Figure 2.1. The backlight emits normally. After the inspection is complete, place the handle lever at 0 scale. 3. The operation handle should be pushed and rotated smoothly and slowly to avoid...

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel. (Note: Each handle has a unique factory number)