User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

WLF-75A non-manual handle, also called emergency helmsman handle, is generally installed in the steering room, control console, bridge wings and other positions, used in the automatic, follow-up steering mode failure when the steering gear operation. The product uses engineering plastic shell beautiful and generous, ball handle is easy to hold, long life contact, with self-resetting spring, let go to return to the median and disconnect the output signal. The product has the following characteristics: 1. Innovative and convenient equipment connection solution, outstanding professional level; High...

2. As shown in 3.2, install the main body inside the C mounting plate and part B outside the plate, and tighten the screws. 3. After installing the handle to the mounting plate, connect electrical cables. After the wiring is completed, it should be confirmed that the external wiring is firm and reliable. 4. Check the external cables, which should be connected normally; Turn the handle, the switch can complete the normal on-off action. After commissioning, disconnect the power supply.

1. Turn the handle to the corresponding position, the contacts are on, and the contacts in other positions are disconnected to realize the switch of the control loop. 2. Release the hand, automatically return to zero position, and all contacts are disconnected. 4.2 Matters needing attention 1. When the product reaches the mechanical life (about 100,000 times), it will not be able to selfreset, please replace it in time. 2. If it is not used according to the requirements in the instructions, the loss shall be borne by the user.

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel.

6.1 Safety protection devices and precautions 1. In the important position of this product, the fastening seals have been processed before leaving the factory, and shall not be disassembled without permission. If the seals are damaged, any product quality problems will be borne by the buyer. 2. Once the product fails to operate normally, please stop using and disconnect the power supply immediately, and contact our after-sales service engineer for a solution. 6.2 Troubleshooting procedures and methods 1. In the process of use, there is an unsolvable fault problem, contact our after-sales service...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 2. Disconnect the external power supply of the product, turn it back and forth regularly, repeat about 10 times, and the cycle is 2 to 3 weeks. It can ensure smooth operation and avoid "aging" phenomenon caused...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. Avoid high temperature exposure or low temperature freezing, which will cause irreversible damage to the damping parts and reduce the service life. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.

9.1 Phone number of the after-sales engineer Manufacturer: Ningbo SHANBEI Technology Co., LTD Address: A2-902, R&D Park, High-tech Zone, Ningbo Postal Code: 310001 Tel: (0574) 87182781 Fax: (0574) 87182781

For more information, please visit:Ningbo Shanbei Technology Co.,Ltd Address: 902 Area A, R&D Park, High-tech Zone, Ningbo, Zhejiang, China WhatsAPP: +86 13186888051 E-mail: [email protected] Wechat: 13186888051