User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

Long-term maintenance and maintenance 9.1 Phone number of the after-sales engineer

The WLF-1 50 steering wheel is used for the follow-up steering control of various types of ships. Inside the steering wheel, there are luminous Pointers and backlit scale plates. The helmsman turns the steering wheel to send the steering order externally. The product has the following characteristics: -Aluminum alloy panel, large scale display area, integrated backlight adjustment, and support for synchronous control of electric axes, as shown in Table 1.1. Basic options (Note: Option 1 is the default option) Products can choose stainless steel handwheel 150S, plastic handwheel 150P and aluminum...

1.3 Product composition Number

The output part provides 16 terminal connections. Please note the distinction in the wiring diagram: 1. Standard version wiring: including 4#, 5#, 6# terminals connected to the steering wheel potentiometer output, 24V power supply for backlight lighting, connected to 13#, 14# terminals. Other terminals are available. 2. Connect two potentiometers: If there are two potentiometers inside, connect them as shown in Figure 2 below.

1. The main body of the steering wheel is made of aluminum alloy, the surface is made of black spray plastic, the main shaft is made of stainless steel, the handwheel can be made of stainless steel, plastic and aluminum alloy, and the internal transmission is made of gear; 2. The scale range is 45-0-45, in the range of ±5 steering order, each scale corresponds to the rotation Angle of 8°, in the range of ±5-45 steering order, each scale corresponds to the rotation Angle of 2.5°, the dial background is black, the scale line and the number are red and green, the panel is equipped with dimming knob,...

Dual channel potentiometer structure 4 to 20mA output wiring diagram Singal Dual Input output output (optional) 4. Backlight adjustment: The film of the steering wheel adopts cold light source design, the panel comes with adjustment knob, and can also be externally dimmed, as shown in Figure 1.5.

1. Remove the four sets of installation accessories (nuts, spring washers, flat washers), as shown in Figure 3.1. Do not remove the installation studs. Set aside 4 sets of accessories, remember not to lose. 2. As shown in FIG. 3.2, place the handwheel vertically in the opening of the mounting plate, and align the screw with the screw hole B. Rotate or tilt the handwheel into the protruding part. 3. As shown in Figure 3.3, fix the handwheel to the mounting plate by installing studs and fittings, and tighten nut C. Make the handwheel and mounting plate tight and reliable. There shall be no gap...

4. Install the handle to the mounting plate and connect electrical cables. After the connection is complete, ensure that the external connection is firm and reliable. 5. Check the external cables, which should be connected normally; The backlight should emit light normally; Push the handle lever, the switch can complete the normal on-off action. After commissioning, disconnect the power supply.

1. The initial position of the steering wheel pointer is in the middle (0 scale), and the resistance value of the corresponding potentiometer (identification number 4, 5 reading) is 2.5KQ± 10%. 2. Switch on the power supply, connect the cable as shown in Figure 1.5, adjust the dimmer knob, the backlight brightness will change, turn the handwheel clockwise or counterclockwise, and the resistance reading between the identification number 4 and 5 is the output value of continuous linear change from 0 to 5KQ. When finished, place the handwheel at 0 mark. 3. The operation of the handwheel rotation...

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel. (Note: Each handle has a unique factory number)

6.1 Safety protection devices and precautions 1. In the important position of this product, the fastening seals have been processed before leaving the factory, and shall not be disassembled without permission. If the seals are damaged, any product quality problems will be borne by the buyer. 2. The damping part used in this product is a loss part, the warranty period is 1 year, effective from the date of delivery; During the warranty period, damping changes, which can not be used normally or seriously affect the operation, shall be maintained by us free of charge. If damping changes occur outside...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 2. Disconnect the external power supply of the product, turn it back and forth regularly, repeat about 10 times, and the cycle is 2 to 3 weeks. It can ensure smooth promotion and avoid the phenomenon of "aging"...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. Avoid high temperature exposure or low temperature freezing, which will cause irreversible damage to the damping parts and reduce the service life. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.