User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

The WLF-100C side push control handle is suitable for the operation of the bow and stern side thrusters. The product has the following characteristics: The product features a chrome-plated appearance, with scale backlight indication. The control damping and gear feedback feel are adjustable. It meets the requirements of electromagnetic compatibility and vibration in the IEC60945 standard, and supports customized functions such as electric shaft synchronization. It has the advantages of fashionable appearance and good hand feel., as shown in Table 1.1. Basic options (Note: Option 1 is the default...

Products have a variety of appearance types that customers can choose according to their needs, as shown in Figure 1.1. According to the number of handles, the products are divided into single-side push 100C1 and double-side push 100C2, as shown in Figure 1.2. When selecting, we should inform our sales staff according to personal needs to avoid unnecessary economic losses!

Each side of the handle provides a separate PCB board, although this is a multi-in-one circuit board, but the production has been fixed in accordance with the requirements of the order to solidify the function (including output signal and dimming signal), each side contains 16 terminals, where P1~P3 is the potentiometer output signal (if any), P4~P5 is the output of 4~20mA (if any), P6 to P7 are commissioning ports, P11 to P12 are dimming ports, and P13 to P14 are DC24V power ports.

shaft is made of stainless steel, and the interior is driven by copper gear. 2. The scale range is 100~0~100, the background color is left red and right green, the scale line and digital white, the backlight is always on, and the brightness can be adjusted by an external dimmer; 3. The operating moment is constant, the rotating moment and the feel of the caton point are adjustable; 4. Potentiometer brand Japan Sakae, model FCP22A, resistance tolerance ±10%, independent linear tolerance 1.0%; 5. Output mode: direct potentiometer linear output, linear relationship with the scale, the theoretical...

2. Mounting panel: The standard mounting panel size of the handle is 96*96mm, in order to reduce the size, you can cancel the mounting panel, the product appearance of the hole size is shown in Figure 2.3:

4. Film scale: The film pasted on the handle is used to indicate the gear position, and different designs can be selected according to the type of propeller. 5. Gear feedback: The handle can provide stuck feedback at a specific gear, such as in the middle zero position or any other gear, and the default output is only stuck feedback at zero position. 6. Output signal: The handle can provide a variety of optional output signals for the control system, including the potentiometer direct output, 4~20mA. Please refer to Figure 1.5 for the connection of the direct output type of potentiometer, and...

4~20mA output & DC0~24V dimming wiring diagram lout+ lout- Each handle provides 16 terminal connections. Terminal 1/2/3 output handle potentiometer signal is used to calculate the current Angle; Terminal 10/11/12 connected to dimmer potentiometer, this part is optional; Terminals 13/14 are used to connect 24V DC power supplies, as shown in Figure 2.8. Some handles adopt the bottom wiring method. Each side of the handle provides 8 terminal connections. Terminals 1/2/3 output the potentiometer signal of the handle for calculating the current Angle, and terminals 5/6 are used for direct dimming,...

1. Remove the four sets of installation accessories (nuts, spring washers, flat washers), as shown in Figure 3.1. Do not remove the installation studs. Set aside 4 sets of accessories, remember not to lose. 2. Place the handle vertically in the opening of the mounting plate as shown in the lower right corner of Figure 3.2, and align the screw with the hole B. Rotate or tilt the handle into the hole when it meets the protruding part. 3. Secure the handle to the mounting plate by installing studs and accessories, and tighten nut C. Make the handle and mounting plate tight and reliable. There should...

4. Install the handle to the mounting plate and connect electrical cables. After the connection is complete, ensure that the external connection is firm and reliable. 5. Check the external cables, which should be connected normally; The backlight should emit light normally; Push the handle lever, the switch can complete the normal on-off action. After commissioning, disconnect the power supply.

Control lever testing adopts two methods: power-on voltage measurement and power-off resistance measurement. The voltage test best simulates actual working conditions and delivers the highest measurement accuracy, so it shall be the preferred method. 1 .Verify normal power supply to the control lever, and set the multi-meter to the DC voltage (VDC) range. 2. Measurement of reference supply voltage Ufs: Locate the two terminals of the potentiometer. Measure the voltage across the terminals with the multi-meter; connect the negative probe to the negative terminal and the positive probe to the positive...

2. As shown in FIG. 4.2, use an Allen wrench at B to rotate and adjust the strength of the push zero feel. Propulsion zero feel adjustment 24V. If the backlight is damaged due to exceeding the rated voltage, the user shall bear the responsibility. 2. In the process of use, when the output of the propulsion direction exceeds the range of 0 ~ 5K, please stop using immediately; When the output value between the identification number 7 and 8 cannot be continuously changed, it should be stopped in time. Method of stopping the service: Disconnect the external power supply. 3. According to the characteristics...