WDI-8AORudder angle distributorUser manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

The WDI-8AO rudder Angle distributor is used to process the rudder Angle signal of the rudder Angle feedback or rudder Angle transmitter, send it to each indicator, and at the same time power the rudder Angle feedback, send the actual rudder Angle signal to the VDR as the NMEA0183 signal. The product adopts engineering plastic shell, beautiful and generous, DIN35 guide rail installation, dual power supply, 8 analog output channels, and system fault alarm output. The product has the following characteristics: 1. Rich interfaces, up to 8 indicators; 2. Dual power supply, isolated channel, stable...

1.5 Product wiring diagramWiring diagram Embedded rudder Angle watch WEI-72/96/144R Three sided rudder Angle watch WCI-400 Wall mounted rudder Angle watch WWI-144 At most eight tables, the eight signals should be consistent, and at the same time 4-20mA or + 10V. Output 8 Output 7 Output 6 Output 5 Output 4 Output 3 Output 2 Output 1 supply communication Other company rudder Angle feedbacks are available

1. Select a suitable position on the inner bottom plate of the driver console and fix it horizontally with DIN35 guide rail; As shown in Figure 3.1, the main body of the rudder Angle distributor is installed on the mounting plate B and fixed on the guide rail through bayonet A to ensure stability and reliability. 2. It is recommended that the distance between the upper and lower cable slots be at least 200mm. It is recommended that 0.5 to 1 square cable be connected and that a cord end terminal be used to connect the cable.

1. Switch on the power supply and connect the cables as shown in Figure 2.4. The power indicator is on. 2. If the feedback works properly, send the rudder Angle data to the distributor, and the RUN indicator light flashes at this time, the distributor will convert the rudder Angle signal into 4~20mA or ±10V, and send it to each indicator. 3. When the system fails, such as rudder Angle data loss, normally open alarm contact P5/P6 is closed. 4. The product can output the rudder Angle data in standard 0183 format, as shown in Figure 4.1. 2. If the CAN bus communication feedback, the maximum distance...

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel.

6.1 Safety protection devices and precautions 1. The important position of this product has been tightened seal processing at the factory, shall not be disassembled without permission, if the seal is damaged, any product quality problems are borne by the buyer. 2. Once the product fails to operate normally, please stop using and disconnect the power supply immediately, and contact our after-sales service engineer for a solution. 6.2 Troubleshooting procedures and methods 1. In the process of use, there is an unsolvable fault problem, contact our after-sales service engineer. 2. During the warranty...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 1. Stop using the device when there is a problem. Contact our after-sales engineer. 2. The input voltage shall be carried out in strict accordance with the wiring instructions. Failure to operate according to...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.

9.1 Phone number of the after-sales engineer Manufacturer: Ningbo SHANBEI Technology Co., LTD Address: A2-902, R&D Park, High-tech Zone, Ningbo Postal Code: 310001 Tel: (0574) 87182781 Fax: (0574) 87182781

For more information, please visit:Ningbo Shanbei Technology Co.,Ltd Address: 902 Area A, R&D Park, High-tech Zone, Ningbo, Zhejiang, China WhatsAPP: +86 13186888051 E-mail: [email protected] Wechat: 13186888051