User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

The WDS-0308 heading distributor is used to amplify the input digital heading signal in NMEA0183 format and output it to other equipment, such as radar, AIS, repeater autopilot, chart chart, etc. It can support various heading sources such as gyrocompass, satellite compass, electronic compass and magnetic compass sensor, and can display the current input heading value at the top of the heading distributor, with signal input and power indicator light, and has four working modes. The product has the characteristics of stable, reliable and easy installation. The product has the following characteristics:...

1.4 Product size drawing Outline dimensional drawing Opening size drawing 72.5mm 1.5 Product wiring diagram 1. Connect the power supply to the 24V DC power supply. 2. Set the working mode and press M to switch Working mode 1 (Default): INPUT1 input, OUTPUT1 to 8 output Working mode 2: INPUT2 input, OUTPUT1 to 8 output Working mode 3: Aviation plug input, OUTPUT1~8 output. Working mode 4: INPUT1 input, OUTPUT1 to 4 output INPUT2 input and OUTPUT5 to 8 output The INPUT1 value is displayed 3. According to actual needs, the output signal is connected to the course signal receiving equipment; 4. Some...

1. As shown in Figure 3.1, install the bow distributor on mounting surface B and tighten screw C to ensure it is secure.

1. Power on the device. The power indicator is on. 2. System self-test, INPUT1, INPUT2, heading sensor aviation plug, there is signal input, the corresponding indicator light, otherwise out, if the communication is unstable, then flashing; 4. Press the RESET button to reset the system. 4.2 Matters needing attention 1. The maximum output power of aviation plug is 2W; 2. If no heading information is displayed within 20 seconds after power-on, the digital tube displays the RXF code.

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel.

6.1 Safety protection devices and precautions 1. In the important position of this product, the fastening seals have been processed before leaving the factory, and shall not be disassembled without permission. If the seals are damaged, any product quality problems will be borne by the buyer. 2. Once the product fails to operate normally, please stop using and disconnect the power supply immediately, and contact our after-sales service engineer for a solution. 6.2 Troubleshooting procedures and methods 1. In the process of use, there is an unsolvable fault problem, contact our after-sales service...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 1. Stop using the device when there is a problem during operation. Contact our after-sales engineer. 2. The input voltage shall be carried out in strict accordance with the wiring instructions. Failure to operate...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. Avoid high temperature exposure or low temperature freezing, which will cause irreversible damage to the damping parts and reduce the service life. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.

9.1 Phone number of the after-sales engineer Manufacturer: Ningbo SHANBEI Technology Co., LTD Address: A2-902, R&D Park, High-tech Zone, Ningbo Postal Code: 310001 Tel: (0574) 87182781 Fax: (0574) 87182781

For more information, please visit:Ningbo Shanbei Technology Co.,Ltd Address: 902 Area A, R&D Park, High-tech Zone, Ningbo, Zhejiang, China WhatsAPP: +86 13186888051 E-mail: [email protected] Wechat: 13186888051