Group: Nautix
Catalog excerpts
Kit for propeller protection (1-c primer + antifouling) Primer Antifouling The printing process may render • PRODUCT DESCRIPTION Made of 2 tins (0.35L anticorrosion primer and 0.35L antifouling for propeller & Z-drives) and gloves, this kit makes easier paint job on propeller & Z-drive. Packaged in box : very easy to use. The primer is a high performance anticorrosion coating, formulated with a Desmodur™ resin which hardens by reacting with air moisture. It is very easy to use and allows application in uncontrolled environment (outdoors). Moreover it can be applied from 0°C, dries quickly and should not be sanded between layers. Applied in 5 layers, this primer offers efficient anticorrosion protection. The antifouling is hard matrix especially developed for propellers and Z drives previously protected with primer. It maintains the propeller in a clean condition ensuring correct balance thus reducing vibration and wear of through-hull seals. PRIMER INFORMATION Finish Coverage Flash point Unit size Typical shelf life Thinner/Cleaner Colour Matt 12m2/L per layer (roller/brush) 23°C <FP<55°C 0.35L 2 years Nautix DP Red Drying / Overcoating Information d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (7C^m wet thickness) - Please refer to Application ANTIFOULING INFORMATION Finish Coverage Flash point Unit size Typical shelf life Thinner/Cleaner Colour Matt 12.5m2/L per layer (roller/brush) 21°C <FP<55°C 0.35L 3 years Nautix DA Black or grey Drying / Overcoating Information d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (10^m wet thickness) - Please refer to Application **Maximum immersion time : several weeks if boat is stored in good conditions TYPE OF SURFACES • Aluminium / Steel / Bronze SURFACE PREPARATION Over bare metal substrate 1) Degrease the surface with Nautix SD (remove all contaminants : oil, grease, salt,...) 2) Rough sand with P4C grade paper to improve adhesion of primer over bare metal, and remove dust neatly. 3) Apply 1 thin layer of primer as soon as possible after sanding. (For aluminium : 5 coats of primer by respecting carefully overcoating intervals) 4) Let dry according to recommendations 5) Apply 5 coats of antifouling by respecting overcoating times Cross movements during application 6) Let dry between layers and before immersion according to our specifications. Maintenance • Remove all non-adherent coating. • Remove oxidation with sandblasting (SA1 minimum), grind or sand with P8C grit • Then follow instructions "over bare metal substrate" from step 3 Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 06/10/2016 Technical recommendation Moisture content of substrate should be checked before any primer application. If necessary after surface preparation, remove any trace of oxidation with needle scaler, rotary wire brushes, grinding disc or sandblasting (finish SA1 minimum). In case of doubt on primer compatibility or quality, remove all the former primer or contact your sales representative.
Open the catalog to page 1PROPPACK Kit for propeller protection (1-c primer + antifouling) Work in well-ventilated area (ensure adequate ventilation during use), wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. Read the label safety section for Health and Safety Information before application. This primer contains isocyanates. Antifouling contains biocides. Use antifouling products with care. Application methods : brush, roller Recommended to apply between 10 and 30°C (but primer...
Open the catalog to page 2All Nautix catalogs and brochures
-
A3 White
2 Pages
-
A3 YACHTING
2 Pages
-
A4 YACHTING
2 Pages
-
A4 White
2 Pages
-
PERFORMER YACHTING
2 Pages
-
DP
1 Pages
-
DA
1 Pages
-
SCOURING ACID
1 Pages
-
POLISH
1 Pages
-
STRIPPER
1 Pages
-
SD DEGRASER
1 Pages
-
NIGHT LIGHT
2 Pages
-
NON-SKID COMPOUNDS
1 Pages
-
NAUTIX GRIP
2 Pages
-
DECK GRIP
2 Pages
-
VA2
2 Pages
-
STARWOOD
2 Pages
-
DB
2 Pages
-
L2
2 Pages
-
STARLAC
2 Pages
-
COOLBLACK
2 Pages
-
BLUE FILLER
2 Pages
-
WATERTIGHT
2 Pages
-
IMPREGARD
2 Pages
-
IMPREWOOD
2 Pages
-
IA
2 Pages
-
ACRALU
2 Pages
-
METAPOX
2 Pages
-
U3
2 Pages
-
U2
2 Pages
-
P7 Spray
2 Pages
-
PA
2 Pages
-
PO
2 Pages
-
HPE
2 Pages
-
EPOXYGARD
2 Pages
-
NX194
2 Pages
-
A8
2 Pages
-
A2
2 Pages
-
A1
2 Pages
-
A3T.Speed
2 Pages
-
MARIN
2 Pages
-
A88 Formula+
2 Pages
-
A9T.Speed
2 Pages
-
A4T.Speed
2 Pages
-
A4 Formula+
2 Pages
-
A7T.Speed™ ANTIFOULING
2 Pages
-
P1
2 Pages
-
A3 Formula+ ANTIFOULING
2 Pages
-
WHITE T.SPEED™
2 Pages
-
NAUTIX MARINE PAINTS
36 Pages