Catalogs >
Nautix >
NAUTIX GRIP

NAUTIX GRIP
2Pages

Catalog excerpts

2-pack transparent non-skid paint The printing process may render some of the colour samples imperfectly. We recommend testing the paint before committing to a colour. PRODUCT DESCRIPTION NAUTIX GRIP is a 2-pack colourless non-skid paint formulated to give the best foot adhesion over deck, bilges or companion way. This product is recommended for solicited areas : deck, windsurf boards,... NAUTIX GRIP is composed of high-quality compounds which bring very good hardness and resistance to abrasion and chemicals. This non-skid paint can be applied over all substrates previously cleaned. Finish Mixing ratio in volume Mixing ratio in weight Coverage Flash point Packaging Shelf life Thinner/Cleaner Colours d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (120pm wet thickness) - Please refer to Application TYPE OF SURFACES • GRP / Composites • Steel (for more details, please refer to our technical specifications for “Steel boat") • Wood (for more details, please refer to our technical specifications for “Wood boat") • Plexiglas Over new surface • Surface must be degreased with Nautix SD and dust free. • Rough sand with 120 grit to favour adherence, Rinse and let dry. Over previously painted surfaces • Check the condition of substrate : the former paint must not come unstuck from the support or must not crumble. Scrape with a brush to check support quality and remove any loosing paint. • Substrate in good condition : - Wash with a suitable detergent, rinse with fresh water (high-pressure water blasting or with brush) and allow to dry. - Degrease the surface with Nautix SD. And then abrade with P120 grade paper. Rinse with fresh water and let dry. • Substrate in poor condition : - Remove all previous coatings. - Surface must be degreased with Nautix SD and dust free. - Rough sand with 80-120 grit to favour adherence. - Rinse with fresh water and let dry. - Apply 1 to 2 coats of U3 or U2 and let dry completely. - Rough sand with 120 grit, rinse and let dry. Technical recommendation Substrate must be cleaned and dried. Please refer to Nautix technical data sheets if you need any further information. To get the best result, we recommend applying a white 2-pack undercoat like U2 or enamel like L2. The substrate should be sanded with 120 paper grit. It's recommended to work in dust-dree environment. Strictly respect drying time before recovering. NAUTIX GRIP is compatible only with 2-pack undercoat or finishing paint. For more information, please check TDS. SAFETY INFORMATION • Work in well-ventilated area (ensure adequate ventilation during use), wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. • Hazardous paint for professionals only. Read the label safety section for Health and Safety Information before application. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 06

Open the catalog to page 1

NAUTIX GRIP 2-pack transparent non-skid paint Application methods : Roller or Spray gun for professionals only. Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : substrate, ambient air and product temperatures must be close. While opening the can, be careful with possible high pressure may cause gush of hardener. Stir or shake individual components thoroughly. Add hardener to the Base, stir and leave for 10 minutes to allow bubbles to disperse. Mix only the necessary...

Open the catalog to page 2