Group: Nautix
Catalog excerpts
MARIN ANTIFOULING iU? ••••••• The printing process may render some of the colour samples imperfectly. We recommend testing the paint before committing to a colour. Mixed matrix - For seasonal use PRODUCT DESCRIPTION Nautix MARIN is a mixed-matrix seasonal antifouling for sailing-, motor-, cruising- and fishing-boats. Nautix MARIN is compatible with most other antifouling types of the market (Please refer to Preparation). PRODUCT INFORMATION Finish Coverage Flash point Unit size Typical shelf life Thinner/Cleaner Matt 12.5m2/L per layer (roller/brush) 21°C < FP < 55°C 0,75L - 2,5L 3 years Nautix DA white, black, blue France, navy blue, red, grey, light Drying / Overcoating Information d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (10C^m wet thickness) -Please refer to Application/ Important points **Maximum immersion time : several weeks if boat is stored in good conditions , dark green SURFACE PREPARATION New hull • The surface should be degreased with Nautix SD and free of all contaminants (oil, grease, salt etc). • Rinse with fresh water and let dry. • Wet-sanding with P120 grade paper to improve adhesion of primer. • Ensure the substrate to be dried, degreased, and free of dust. • Apply adapted primer. Previously antifouled surface Check the substrate : Before overcoating, remove all loosely adhering and flaking paint, feather back all edges. You can grit with brush in different areas to test adhesion of current antifouling. • Protected surface in good condition (hard matrix) : - Clean the entire hull with controlled high pressure washing or brush. - Sand surface with wet P80-120 paper grade. - Rinse with fresh water and let dry. • Surface in poor condition or self-polishing antifouling : - Remove all traces of antifouling by abrasion, sweep blasting or using Nautix STRIPPER. - Degrease with Nautix SD. - Sand primer with wet P80-120 paper grade. - Rinse with fresh water and let dry. - Seal eventually with suitable Nautix primer. Important information Surface preparation is very important step to get long-efficiency antifouling. Choose the right primer (1 coat for adhesion - 3-5 coats for protection) : - Polyester : P1 - HPE - PE - PO - EPOXYGARD - Wood : P1 (1st layer : mix with thinner DP 30% max) - Plywood : HPE - EPOXYGARD (+ IMPREGARD) - Steel : PA - EPOXYGARD Important : - This antifouling cannot be applied over aluminium hull. - Do not overcoat with hard matrix antifouling. If there is any doubt on compatibility between the new antifouling paint and the existing one, apply a coat of Nautix P1. SAFETY INFORMATION • Only use as an antifouling product to prevent the growth of micro and macro organisms like week, algae or barnacles from settling on underwater surfaces in salt and fresh water. For amateur (up to 2.5Litres) and professional (up to 20 litres). Antifouling contains biocides. Use antifouling products with care. • Work in well-ventilated area, wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 06/10/2016
Open the catalog to page 1MARIN ANTIFOULING Mixed matrix – For seasonal use Application methods : Airless, Airmix spray, brush, roller. Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : substrate, ambient air and product temperatures must be close. Avoid applying in adverse weather conditions : strong wind, strong sunlight, high/low temperatures, high humidity or rain. Important : Antifouling efficiency depends directly on applied film thickness. Apply the whole recommended quantity (excl....
Open the catalog to page 2All Nautix catalogs and brochures
-
A3 White
2 Pages
-
A3 YACHTING
2 Pages
-
A4 YACHTING
2 Pages
-
A4 White
2 Pages
-
PERFORMER YACHTING
2 Pages
-
DP
1 Pages
-
DA
1 Pages
-
SCOURING ACID
1 Pages
-
POLISH
1 Pages
-
STRIPPER
1 Pages
-
SD DEGRASER
1 Pages
-
NIGHT LIGHT
2 Pages
-
NON-SKID COMPOUNDS
1 Pages
-
NAUTIX GRIP
2 Pages
-
DECK GRIP
2 Pages
-
VA2
2 Pages
-
STARWOOD
2 Pages
-
DB
2 Pages
-
L2
2 Pages
-
STARLAC
2 Pages
-
COOLBLACK
2 Pages
-
BLUE FILLER
2 Pages
-
WATERTIGHT
2 Pages
-
IMPREGARD
2 Pages
-
IMPREWOOD
2 Pages
-
IA
2 Pages
-
ACRALU
2 Pages
-
METAPOX
2 Pages
-
U3
2 Pages
-
U2
2 Pages
-
P7 Spray
2 Pages
-
PA
2 Pages
-
PO
2 Pages
-
HPE
2 Pages
-
EPOXYGARD
2 Pages
-
NX194
2 Pages
-
A8
2 Pages
-
PROPPACK
2 Pages
-
A2
2 Pages
-
A1
2 Pages
-
A3T.Speed
2 Pages
-
A88 Formula+
2 Pages
-
A9T.Speed
2 Pages
-
A4T.Speed
2 Pages
-
A4 Formula+
2 Pages
-
A7T.Speed™ ANTIFOULING
2 Pages
-
P1
2 Pages
-
A3 Formula+ ANTIFOULING
2 Pages
-
WHITE T.SPEED™
2 Pages
-
NAUTIX MARINE PAINTS
36 Pages