Catalogs >
Nautix >
L2

L2
2Pages

Catalog excerpts

2-pack high performance gloss marine Topside Finish •••••••••••• fluo The printing process may render some of the colour samples imperfectly. We recommend testing the paint b^ore committing to a colour. PRODUCT DESCRIPTION Nautix L2 is the ultimate performing, high-gloss 2-pack polyurethane topside finish that has superb colour retention, together with outstanding chemical and abrasion resistance. It provides the longest-lasting, ultra-high gloss finish. This finishing paint is very easy to apply and contains UV filter for increased durability. L2 can be applied over all substrates above the waterline. This enamel has been formulated specifically to enable skilled amateur users to achieve professional quality results with ease. PRODUCT INFORMATION Finish Mixing ratio in volume Mixing ratio in weight Coverage Flash point Packaging Shelf life Thinner/Cleaner Colours Drying / Overcoating Information d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (80um wet thickness) - Please refer to Application High gloss 3 base / 1 hardener 4 base / 1 hardener 12m2/L per layer (roller/brush) 23°C <FP<55°C 0.75L - 2L 5 years Nautix DP white, light off-white, light ivory, light grey, anthracite grey, black, sunset yellow, orange rescue, bright red, sky blue, blue France, midnight blue, navy blue, orange fluo, British green, golf green TYPE OF SURFACES - GRP / Composites - Plywood - Steel (for more details, please refer to our technical specifications for “Steel boat") - Carbon SURFACE PREPARATION The surface must be dried and degreased before application. Check undercoat TDS for more information. Over U2 undercoat • Rough sand with 240 grit to favour adherence, Rinse and let dry. Over previously painted surfaces • Check the condition of substrate : the former paint must not come unstuck from the support or must not crumble. Scrape with a brush to check support quality and remove any loosing paint. • Substrate in good condition : - Wash with a suitable detergent, rinse with fresh water (high-pressure water blasting or with brush) and allow to dry. - Degrease the surface with Nautix SD. And then abrade with P240 grade paper. Rinse with fresh water and let dry. • Substrate in poor condition : - Remove all previous coatings. - Surface must be degreased with Nautix SD and dust free. - Rough sand with 120 grit to favour adherence. - Rinse with fresh water and let dry. - Apply 1 to 2 coats of U2 and let dry completely. - Rough sand with 240 grit, rinse and let dry. Application advices To get the best result, we recommend to apply U2 white undercoat. The support should be sanded with P240 grade paper. Important: enamel application should be done far away from dust. Strictly respect drying time before recovering. L2 is compatible only with 2-pack undercoat (U2, HPE, PE) or 2-pack enamel (L2). Please refer to Nautix technical data sheets if you need any further information. SAFETY INFORMATION • Work in well-ventilated area (ensure adequate ventilation during use), wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. • Hazardous paint for professionals only. Read the label safety section for Health and Safety Information before application. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 06/10/2016

Open the catalog to page 1

L2 2-pack high performance gloss marine Topside Finish Application methods : brush, roller. Spray gun for professionals only. Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : substrate, ambient air and product temperatures must be close. While opening the can, be careful with possible high pressure may cause gush of hardener. Stir or shake individual components thoroughly. Add hardener to the Base, stir and leave for 10 minutes to allow bubbles to disperse. Mix only...

Open the catalog to page 2