Catalogs >
Nautix >
DECK GRIP

DECK GRIP
2Pages

Catalog excerpts

DECK GRIP l-pack non-skid deck paint — OK The printing process may render some of the colour samples imperfectly. We recommend testing the paint before committing to a colour. PRODUCT DESCRIPTION Nautix DECK GRIP is a non-skid fast-drying deck paint formulated for marine environment. Easy to apply and very resistant to abrasion and detergents, this product is recommended for application over deck and bilges. Applied in thin coat, DECK GRIP provides an excellent slip resistant finish and it will give a good foot adhesion over deck. This paint has low sheen finish to prevent sunlight dazzle, and is suitable for all substrates. PRODUCT INFORMATION Finish Coverage Flash point Unit size Typical shelf life Thinner/Cleaner Colours Matt 8m2/L per layer (roller/brush) 23°C <FP<55°C 0.75L 5 years Nautix DA white, light grey, transparent Drying / Overcoating Information d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (120pm wet thickness) - Please refer to Application TYPE OF SURFACES • GRP / Composites • Steel (for more details, please refer to our technical specifications for “Steel boat") • Aluminium (for more details, please refer to our technical specifications for “Aluminium boat") • Wood (for more details, please refer to our technical specifications for “Wood boat") SURFACE PREPARATION Over new surface • Surface must be degreased with Nautix SD and dust free. • Rough sand with 120 grit to favour adherence, Rinse and let dry. Technical recommendation Over previously painted surfaces • Check the condition of substrate : the former paint must not come unstuck from the support or must not crumble. Scrape with a brush to check support quality and remove any loosing paint. • Substrate in good condition : - Wash with a suitable detergent, rinse with fresh water (high-pressure water blasting or with brush) and allow to dry. - Degrease the surface with Nautix SD. And then abrade with P120 grade paper. Rinse with fresh water and let dry. • Substrate in poor condition : - Remove all previous coatings. - Surface must be degreased with Nautix SD and dust free. - Rough sand with 80-120 grit to favour adherence. - Rinse with fresh water and let dry. - Apply 1 to 2 coats of U3 or U2 and let dry completely. - Rough sand with 120 grit, rinse and let dry. SAFETY INFORMATION Substrate must be cleaned and dried. Please refer to Nautix technical data sheets if you need any further information. To get the best result, we recommend applying a white undercoat like U3 or U2. The support should be sanded with 120 paper grit. It's recommended to work in dust-dree environment. Strictly respect drying time before recovering. DECK GRIP is compatible will all materials (wood, plywood, GRP, aluminium, and steel). For more information, please check TDS. • Work in well-ventilated area (ensure adequate ventilation during use), wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. • Read the label safety section for Health and Safety Information before application. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 06/10/2016

Open the catalog to page 1

DECK GRIP 1-pack non-skid deck paint Application methods : roller, spray gun (gravity feed cup). Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : substrate, ambient air and product temperatures must be close. Homogenize the product with a blender. You can use thinner if necessary. Thinning makes easier application, but can also weaken the film. Respect carefully overcoating time. Favour natural solvent evaporation and do not heat ambient air after beginning of...

Open the catalog to page 2