Catalogs >
Nautix >
DB

DB
2Pages

Catalog excerpts

DB 1-pack hard wearing coating for bilges i?« o* The printing process may render some of the colour samples imperfectly. We recommend testing the paint before committing to a colour. PRODUCT DESCRIPTION Nautix DB finishing paint protects bilges, lockers and bulkheads against moisture penetration, oil, fuel, wear, and tear. This paint offers high opacity for an excellent covering power. 1-pack DB paint builds a very hard and smooth film for a limited adhesion of dust for an easy cleaning of your boat bilges, bulkheads and lockers. Nautix DB can be applied on any material (GRP, epoxy, wood, aluminium, steel) previously coated with the appropriate primer. PRODUCT INFORMATION Finish Coverage Flash point Unit size Typical shelf life Thinner/Cleaner Colours Gloss 10m2/L per layer (roller/brush) 23°C <FP<55°C 0.75L - 2.5L 5 years Nautix WS White, dark grey Drying / Overcoating Information d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (100pm wet thickness) - Please refer to Application/ Important points TYPE OF SURFACES • GRP / Composites • Steel (for more details, please refer to our technical specifications for “Steel boat") • Wood (for more details, please refer to our technical specifications for “Wood boat") SURFACE PREPARATION New surface • The surface should be degreased with Nautix SD and free of all contaminants (oil, grease, salt etc). • Sand with P120 grade paper to improve adhesion of paint. • Rinse with fresh water and let dry. • Ensure the substrate to be dried, degreased, and free of dust. Over previously painted surfaces • Check the condition of substrate : the former paint must not come unstuck from the support or must not crumble. Scrape with a brush to check support quality and remove any loosing paint. • Substrate in good condition : - Wash with a suitable detergent, rinse with fresh water (high-pressure water blasting or with brush) and allow to dry. - Degrease the surface with Nautix SD. And then abrade with P240 grade paper. - Rinse with fresh water and let dry. • Substrate in poor condition : - Remove all previous coatings. - Surface must be degreased with Nautix SD and dust free. - Rough sand with 120 grit to favour adherence. - Rinse with fresh water and let dry. - Apply 1 to 2 coats of U3 or U2 and let dry completely. - Rough sand with 240 grit, rinse and let dry. SAFETY INFORMATION Technical recommendation Substrate must be cleaned and dried. Please refer to Nautix undercoats technical data sheets if you need any further information. It's recommended to work in dust-dree environment. DB is compatible will all materials (wood, plywood, GRP and steel). Nautix DB can be applied over 1-pack and 2-pack undercoats/primers. • Work in well-ventilated area (ensure adequate ventilation during use), wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. • Read the label safety section for Health and Safety Information before application. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 09/03/2017

Open the catalog to page 1

DB 1-pack hard wearing coating for bilges Application methods : brush, roller, spray gun , airless. Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : substrate, ambient air and product temperatures must be close. Homogenize the product with a blender. It’s recommended to sand with P400 grade paper between coats. Respect carefully overcoating time. Favour natural solvent evaporation and do not heat ambient air after beginning of application. Do not use ventilator or...

Open the catalog to page 2