Group: Nautix
Catalog excerpts
A4 White Hard matrix antifouling - For all year frequent use or at high-speed service The printing process may render some of the colour samples imperfectly. We recommend testing the paint before committing to a colour. PRODUCT DESCRIPTION Nautix A4 White is high-performance hard matrix antifouling paint recommended for sailing-, power-, and leisure fishing-boats, but also for boat dry's out between tides and trailer-boats. The formulation of Nautix A4 White brings a very smooth finish and a very high level of protection in medium to heavy fouling areas. Ideal for frequent use and for boats remaining in water all the yearlong, this antifouling offers hard, scrubbable finish to allow clean off if needed. Nautix A4 White is compatible with most other antifouling types on the market (in good condition). However it cannot be applied over ablative antifouling. d=days h=hours min=minutes *Minimum overcoating time recommended for 1 layer (10C^m wet thickness) - Please refer to Application/ Important points **Maximum time before immersion : several weeks if boat is stored in good conditions Important information Surface preparation is very important step to get long-efficiency antifouling. Choose the right primer (1 coat for adhesion - 3-5 coats for protection) : - Polyester : P1 - HPE - PE - PO - EPOXYGARD - Wood : P1 (1st layer : mix with thinner DP 30% max) - Plywood : HPE - EPOXYGARD (+ IMPREGARD) - Steel : PA - EPOXYGARD Important : - Do not apply over aluminium hull. - Do not apply over SPC paint. - Do not apply over ablative antifouling. If there is any doubt on compatibility between the new antifouling paint and the existing one, apply a coat of Nautix P1. Finish Coverage Flash point Unit size Typical shelf life Product condition Thinner/Cleaner Colour Matt 10m2/L per layer (see "application" section for details) 21°C < FP < 55°C 0,75L - 2,5L - 20L 24 months Ready for use Nautix DA White New hull • The surface should be degreased with Nautix SD and free of all contaminants (oil, grease, salt etc). • Rinse with fresh water and let dry. • Wet-sanding with P120 grade paper to improve adhesion of primer. • Ensure the substrate is dry, degreased, and free of dust. • Apply adapted primer. Previously antifouled surface Check the substrate : Before overcoating, remove all loosely adhering and flaking paint, feather back all edges. You can grit with brush in different areas to test adhesion of current antifouling. • Protected surface in good condition (hard matrix only) : - Clean the entire hull with controlled high pressure washing or brush. - Sand surface with wet P80-120 paper grade. - Rinse with fresh water and let dry. • Surface in poor condition (or ablative /mixed matrix antifouling) : - Remove all traces of antifouling by abrasion, sweep blasting or using Nautix STRIPPER. - Degrease with Nautix SD. - Sand primer with wet P80-120 paper grade. - Rinse with fresh water and let dry. - Seal eventually with suitable Nautix primer. • Only use as an antifouling product to prevent the growth of micro and macro organisms like weed, algae or barnacles from settling on underwater surfaces in salt water. For amateur and professional (up to 5 litres pack sizes). Antifouling products contain biocides. Read instructions and use with care. • Work in well-ventilated area, wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environment! 19/02/2018
Open the catalog to page 1A4 White Hard matrix antifouling – For all year frequent use or at high-speed service Application methods : brush, roller, conventional spray gun, airless. Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : Substrate, ambient air and product temperatures must be close. Avoid applying in adverse weather conditions : Strong wind, strong sunlight, high/low temperatures, high humidity or rain. Important : Antifouling efficiency depends directly on applied film thickness....
Open the catalog to page 2All Nautix catalogs and brochures
-
A3 White
2 Pages
-
A3 YACHTING
2 Pages
-
A4 YACHTING
2 Pages
-
PERFORMER YACHTING
2 Pages
-
DP
1 Pages
-
DA
1 Pages
-
SCOURING ACID
1 Pages
-
POLISH
1 Pages
-
STRIPPER
1 Pages
-
SD DEGRASER
1 Pages
-
NIGHT LIGHT
2 Pages
-
NON-SKID COMPOUNDS
1 Pages
-
NAUTIX GRIP
2 Pages
-
DECK GRIP
2 Pages
-
VA2
2 Pages
-
STARWOOD
2 Pages
-
DB
2 Pages
-
L2
2 Pages
-
STARLAC
2 Pages
-
COOLBLACK
2 Pages
-
BLUE FILLER
2 Pages
-
WATERTIGHT
2 Pages
-
IMPREGARD
2 Pages
-
IMPREWOOD
2 Pages
-
IA
2 Pages
-
ACRALU
2 Pages
-
METAPOX
2 Pages
-
U3
2 Pages
-
U2
2 Pages
-
P7 Spray
2 Pages
-
PA
2 Pages
-
PO
2 Pages
-
HPE
2 Pages
-
EPOXYGARD
2 Pages
-
NX194
2 Pages
-
A8
2 Pages
-
PROPPACK
2 Pages
-
A2
2 Pages
-
A1
2 Pages
-
A3T.Speed
2 Pages
-
MARIN
2 Pages
-
A88 Formula+
2 Pages
-
A9T.Speed
2 Pages
-
A4T.Speed
2 Pages
-
A4 Formula+
2 Pages
-
A7T.Speed™ ANTIFOULING
2 Pages
-
P1
2 Pages
-
A3 Formula+ ANTIFOULING
2 Pages
-
WHITE T.SPEED™
2 Pages
-
NAUTIX MARINE PAINTS
36 Pages