manual toilet
4Pages

{{requestButtons}}

Catalog excerpts

manual toilet - 1

1 MANUAL TOILETS: - Compact Model - Comfort Model This toilet may be supplied in the standard and large bowl versions and is equipped with a new conceiving of manual toilet pump offering the following qualities: • Thanks to the proper button hole-shaped fixing holes on the base, it is possible to replace the toilet without having to bore new holes (easy substitution with toilets by PAR, RM and many others) to do so. • All mouldings are made of a kind of plastic material fully resistant against uric acids as well as against the chemical agents contained in the detergents which are normally employed to keep the toilet clean. • The complete opening from top of the piston allows a quick cleansing without disassembling the toilet from the base. • The toilet may be mounted both above and below the waterline. The pump is a self-priming one. • The reversible left- handed pump mounting enables to install the toilet indifferently on both sides. • Waste discharge is possible both overboard and into holding tanks on board. • The toilet is equipped with luxury baked enamel painted wooden seat and cover Fitting details: Connections for 19 mm. (3/4") inlet hose and 38 mm. (1 1/2") outlet hose Dimensions: Standard: width cm. 45 x depth cm. 41 x height cm. 34 (17 3/4" x 16" x 13 1/2 ") Weight: Standard model: kg. 10 about CD: 6500000700 - equipped with wooden seat CD: 6700000700 - equipped with plastic seat Fitting details: Connections for 19 mm. (3/4") inlet hose and 38 mm. (1 1/2") outlet hose Dimensions: width cm. 47 x depth cm. 48 x height cm. 35 (18 1/2" x 19 x 13 3/4") Weight: Kg.11 about CD: 6500000800 - equipped with wooden seat SPARE PART LIST 1) 6500000001 WOODEN SEAT 6500000003 WOODEN LARGE SEAT 2) 6500000002 PLASTIC SEAT 4) 6500000012 HINGE GROUP PLASTIC SEAT 5) 6500000500 PORCELAIN STANDARD BOWL 6) 6500000510 PORCELAIN LARGE BOWL 7) 6500000550 INTAKE ELBOW 9) 6000000770 PUMP 10) 6100000777 PLASTIC BASE 11) 6000000702 INTAKE FLANGE GASKET 12) 6000000704 INTAKE FLANGE 13) 6000000708 PUMP SHAFT 14) PL000WM003 PLASTIC WASHER 16) PL000WM006 PLASTIC HANDLE 17) 6000000703 VALVE CONTROL GROUP 18) PL000W9009 OUTLET ELBOW GROUP 19) 6000000705 PUMP CAMME 20) 6000000709 PUMP BASE GASKET 21) 6000000711 OUTLET FLANGE GASKET 22) 6000007011 BOWL GASKET/SCREWS 23) 6500000000 GASKET KIT 24) 6500001000 BRYDON GASKET KIT 25) 6500100000 PAR GASKET KIT

Open the catalog to page 1
manual toilet - 2

2 OPERATING INSTRUCTIONS INTRODUCTION: The toilet is one of the most employed equipments on your boat. A correct operation of the toilet is essential for the safety and the comfort of your crew and your craft. HAZARD RISK: ACCIDENTAL DAMAGE : If the toilet is connected to any through-hull fittings and if either the toilet or the pipework is damaged, water may flood in, causing the craft to sink, which may result in loss of life. Therefore, after each usage, both seacocks (or secondary valves) must be shut. Whenever your craft is unattended, even if only for a very short period of time, both...

Open the catalog to page 2
manual toilet - 3

3 .3 Toilet below the waterline and discharging overboard: You will need a 38 mm. (1 1/2") Vented Loop fitting - Arrange the oulet hose, so that its highest point is is at least 20 cm. (8') above the waterline, and fit the Vented Loop in that point 4.4 Toilet above the waterline and discharging overboard: You may need a 38 mm. (1 1/2") Vented Loop fitting - Run the outlet hose up from the discharge elbow, at least 30 cm. (12') above the discharge elbow. Then fit a Vented Loop on top of the hose, ensuring in this way to keep some water in the base of the toilet without risk of it being...

Open the catalog to page 3
manual toilet - 4

4 - Unscrew the seal assembly and slide it off the piston. Wrap one turn of tape around the thread at the top of the piston rod to protect the new seal, slide the new seal down the piston rod and tighten it. Remove the tape from the thread. Replace the bumper washer and the handle, absolutely by gripping the piston rod through the tape. Then remove the tape from the piston rod., 3. SERVICING: Winterization. Drain the complete system both as a protection against frost damage and to avoid the growth in the pipework of bacteria that could cause unpleasant smells. Warning: THE USE OF...

Open the catalog to page 4

All Matromarine Products catalogs and brochures

  1. Blower

    2 Pages

  2. Power Trim

    1 Pages

  3. Deck Pump

    2 Pages

Archived catalogs