manual toilet 99
4Pages

1 MANUAL TOILETS: -New Compact Model -New Comfort Model This toilet may be supplied in the standard and large bowl versions and is equipped with a new conceiving of manual toilet pump offering the following qualities: • Thanks to the proper button hole-shaped fixing holes on the base, it is possible to replace the toilet without having to bore new holes (easy substitution with toilets by PAR, RM and many others) to do so. • All mouldings are made of a kind of plastic material fully resistant against uric acids as well as against the chemical agents contained in the detergents which are normally employed to keep the toilet clean. • The complete opening from top of the piston allows a quick cleansing without disassembling the toilet from the base. • The toilet may be mounted both above and below the waterline. The pump is a self-priming one. • The reversible left- handed pump mounting enables to install the toilet indifferently on both sides. • Waste discharge is possible both overboard and into holding tanks on board. • The toilet is equipped with luxury baked enamel painted wooden seat and cover Fitting details: Connections for 19 mm. (3/4") inlet hose and 38 mm. (1 112") outlet hose Dimensions: Standard: width cm. 45 x depth cm. 41 x height cm. 34 (17 3/4" x 16" x 13 1/2 ") Weight: Standard model: kg. 10 about CD: 6600000700 - equipped with wooden seat CD: 6600200700 - equipped with plastic seat Fitting details: Connections for 19 mm. W4") inlet hose and 38 mm. (1 112") outlet hose Dimensions: width cm. 47 x depth cm. 48 x height cm. 35 (18 1/2" x 19 x 13 3/4") Weight: Kg.11 about CD: 6600000800 - equipped with wooden seat SPARE PARTS: ART. 6500000001 WHITE WOODEN SEAT (1) ART. 6000000706/7/11 OUTLATE/FLANGE ELBOW/GASKET (5) ART. 6500000500 COMPACT PORCELAIN BOWL (2) ART. 6100000777 TOILET BASE (6) ART. 6500000550 INTAKE ELBOW (3) The large toilet bowl has the following code ART 6500000510 ART. 6500011000 GASKET KIT (4)

2 OPERATING INSTRUCTIONS INTRODUCTION: The toilet is one of the most employed equipment on your boat. A correct operation of the toilet is essential for the safety and the comfort of your crew and your craft. HAZARD RISK: ACCIDENTAL DAMAGE : If the toilet is connected to any through-hull fittings and if either the toilet or the pipework is damaged, water may flood in, causing the craft to sink, which may result in loss of life. Therefore, after each usage, both seacocks (or secondary valves) must be shut. Whenever your craft is unattended, even if only for a very short period of time, both...

3 4.3 Toilet below the waterline and discharging overboard: You will need a 38 mm. (1 1/2") Vented Loop fitting - Arrange the outlet hose, so that its highest point is is at least 20 cm. (8') above the waterline, and fit the Vented Loop in that point 4.4 Toilet above the waterline and discharging overboard: You may need a 38 mm. (1 1/2") Vented Loop fitting - Run the outlet hose up from the discharge elbow, at least 30 cm. (12') above the discharge elbow. Then fit a Vented Loop on top of the hose, ensuring in this way to keep some water in the base of the toilet without risk of it being...

4 - Unscrew the seal assembly and slide it off the piston. Wrap one turn of tape around the thread at the top of the piston rod to protect the new seal, slide the new seal down the piston rod and tighten it. Remove the tape from the thread. Replace the bumper washer and the handle, absolutely by gripping the piston rod through the tape. Then remove the tape from the piston rod., 3. SERVICING: Winterization. Drain the complete system both as a protection against frost damage and to avoid the growth in the pipework of bacteria that could cause unpleasant smells. Warning: THE USE OF...