- Catalogs
- Maritronix
- PILOT-H
PILOT-H
PILOT-H
- Transmitter: Dimensions 70×185×40mm, Weight 210g, Case material PA6GF30, Power LR6(AA)1.5Vx2, Operating temperature -35°C to +75°C, Protection level IP65, FCC and CE certified.
- Receiver: Dimensions 260×167×82mm, Weight 2500g, Case material aluminium, Power 12V/24V DC, Operating temperature -35°C to +75°C, Protection level IP65 with hydrophobic vent, FCC and CE certified.
- Includes 1 transmitter, 1 receiver, 2 mounting plates, 1 antenna, 1 universal cable set, 1 external buzzer, 1 user manual, 1 installation manual, 1 lanyard, and 1 protective case for the transmitter.
- Engine Control: Engage engines forward or reverse using designated buttons. For single-engine boats, specific buttons are used for forward and reverse.
- Bow and Stern Thrusters: Operate thrusters if installed and configured. Specific buttons control direction.
- Anchor Winch: Raise or lower the anchor using a combination of buttons.
- Horn Activation: Use stern thruster buttons with the start button to activate the horn.
- Accessible via Wi-Fi compatible devices. No additional software required, ensuring long-term usability.
- Includes a 2000mm high-quality cable set with labeled connectors for easy installation. Pre-wired T cross connectors available for certain models.
- Compatible with most analog proportional control systems. Additional modules may be required for certain systems, available from Maritronix.
- For systems using CAN bus protocol, a gateway is needed for thruster control.
- Direct gearbox control can be enabled in the configuration menu.
- Detailed list of compatible systems with corresponding SYS IDs for ordering and installation purposes.
Catalog excerpts
WIRELESS HANDHELD REMOTE CONTROL RT TA
Open the catalog to page 1
SPECIFICATIONS TRANSMITTER Dimensions Weight Case material Power Operating temperature Protection level RECEIVER Dimensions Weight Case material Power Operating temperature Protection level FCC certified CE certified THE SCOPE OF DELIVERY FOR A PILOT-H INCLUDES: 1 transmitter 1 receiver 2 mounting plates for receiver 1 antenna for receiver 1 universal cable set 1 external buzzer 1 user manual 1 installation manual 1 lanyard 1 protective case for transmitter
Open the catalog to page 2
REMOTE CONTROLLER (TRANSMITTER) TAKE COMMAND Activate helm control by pressing the start button while the remote control is already turned on. Depending on your boat’s propulsion system and the configuration of the Pilot-H, it may be necessary to first manually activate the station to which the Pilot-H is connected. BOW THRUSTER Activate the bow thruster to push the bow to port by pressing the upper left button(1). Press the upper right button(2) to push the bow to starboard. These buttons will only operate a bow thruster if it is installed on the boat and the Pilot-H Receiver is configured accordingly....
Open the catalog to page 3
WORKING ALGORITHM AND CONNECTION SCHEME The Pilot-H system is connected between the control head and the engine ECU. When the engine command button on the Pilot-H transmitter is pressed, it emulates the control head commands and transmits them to the engine control unit. Upon releasing the button or switching off the remote control, the connection between the control head and the engine ECU is promptly restored. This method of connection ensures both safety and reliability. CONTROL HEAD A 2000mm high-quality cable set is included in each package. Each cable features an individual connector, number,...
Open the catalog to page 4
PILOT-H INSTALLATION: COMPATIBILITY, ADDITIONAL MODULES AND INSTRUCTIONS. PILOT-H is compatible with most analog proportional control systems. Please refer to the list of commonly installed analog propulsion control and thruster systems. Note that some manufacturers are not listed because they share the same control panels. In some cases, an additional module is required to connect PILOT-H, especially with analog proportional thruster control panels. This module can be purchased directly from Maritronix. For correct installation, review the datasheet and connection schematics of the installed...
Open the catalog to page 5
VOLVO PENTA ANALOG CONTROLS
Open the catalog to page 6
ZF MICROCOMMANDER CLEARCOMMAND CRUISECOMMAND MINICOMMAND ANALOG CONTROLS
Open the catalog to page 7
HONDA ANALOG
Open the catalog to page 9
MERCURY ANALOG MERCURY JOYSTICK PILOTING 1 SUZUKI PRECISION CONTROL ANALOG
Open the catalog to page 10
TWIN DISC EC200,EC300 ANALOG YAMAHA ANALOG
Open the catalog to page 11
SIDE POWER
Open the catalog to page 12
SIDE POWER TYPE: PROPORTIONAL SYS ID: 507 + S-LINK INT 8730B BOW TYPE: PROPORTIONAL SYS ID: 508 + S-LINK INT 8730S STERN TYPE: ON/OFF/PROPORTIONAL SYS ID: 509 ABT TYPE: ON/OFF/PROPORTIONAL SYS ID: 510
Open the catalog to page 13
TYPE: ON/OFF SYS ID: 513 BCS TYPE: ON/OFF SYS ID: 514
Open the catalog to page 14
TYPE: ON/OFF SYS ID: 518 CRAFTSMAN TYPE: ON/OFF SYS ID: 519 KOBELT KEYPOWER
Open the catalog to page 15
TYPE: ON/OFF SYS ID: 525 QUICK TYPE: ON/OFF SYS ID: 526
Open the catalog to page 16
TYPE: ON/OFF VETUS
Open the catalog to page 17
ENGBO XFORCE NAIAD MARINE SYSTEMS
Open the catalog to page 18
ANCHOR WINCHES NONSPECIFIC BRANDS The reverse rotation delay is set through the Pilot-H's configuration program.
Open the catalog to page 19All Maritronix catalogs and brochures
PILOT-H6 Pages
Maritronix MPC241 Page
FLEXBALL 50002 Pages
FLIR M2322 Pages
- Boat screen
- Ship screen
- Boat remote control
- Wireless remote control
- Control screen
- Boat joystick
- Remote control with buttons
- Ship joystick
- Waterproof screen
- Thruster remote control
- Windlass remote control
- Multifunction remote control
- Motor remote control
- Anchor remote control
- Waterproof remote control
- Remote control with joystick
- Ship remote control
- Yacht remote control
- Winch remote control
- Lateral thruster joystick