The Electrolux Dishwashing range is produced for customers with the highest conceivable demands for good efficiency, economy and ergonomics for dishwashing operation. The rack type dishwasher WTM200 has a capacity up to 200 racks per hour with 2 speeds. The range consists of 2 electrically heated models (feed from left or right) available with or without Energy Saving Device (ESD). EASY TO INSTALL • Solid 3mm square stainless steel sub-frame with bolt-together construction that can be delivered assembled or in modules to be connected on site. • Stainless steel wash pumps. • Brass inlet valves as standard. • All rear positioned water tubes in stainless steel. • Only one cable for electrical connection. • Electrical and water connections centralized in one area • Service from the front and from the side. • Prearrangements for automatic detergent dispenser, energy management device and HACCP implementation. FUNCTIONAL ZONES • Separate 45 litre pre-wash zone without detergent for maximum dirt removal incorporates automatic partial drain. • Power wash zone where all the soil is removed with Maximum Water contact wash arms. • Rinse area equipped with the DUO-rinse system • Atmospheric boiler combined with the rinse booster pump for perfect rinsing performances in terms of sanitation, energy saving, independence from the water pressure on the network. • Incorporates non-return (air gap class A) valve. • Can be equipped with a drying zone for fast and efficient drying (optional extra). EASY TO CLEAN AND MAINTAIN • The rinse & wash tank is pressed with completely rounded corners and sloping base. • Smooth surfaces. Main internal components made in 304 AISI stainless steel as well as the external panels. • Easy removable ash arms and double tank filter (flat and deep box). • Height adjustable stainless steel feet. • Self-draining wash pumps provide maximum hygiene. • Hinged flap for easy access to the energy saving condenser unit. • Large balanced inspection doors for easy access to wash area. • Self-cleaning cycle in pre-wash,wash & rinse zones. EASY TO USE • Automatic start/stop function. • Simple electric control panel. • Counter balanced door with safety switch and easy to grip handle. • Built-in rinse water heater to increase the temperature of the final rinse water. • Electronic control panel with autodiagnostic check control. EASY ON THE ENVIRONMENT • 35mm thickness foam injection insulated doors • 98% recyclable by weight. • CFC free packaging. • Low noise level <70dBA. For further specifications and optional extras, please see overleaf.

DISHWASHER WTM200 – FEED FROM LEFT Dimensions mm 560 1. Main switch 2. Mains supply connection 3. Hot water connection, temperature ca 50°C , ISO 228/1 DN 20 (G 3/4"), pressure 150– 700 kPa (1.5-7 bar) at 0.3 l/sec. 4. Cold water connection, temperature ca15°C , ISO 228/1 DN 20 (G 3/4"), pressure 150– 700 kPa (1.5-7 bar) at 0.3 l/sec. 5. Drain outlet 1 1/2" M, flow rate 120 l/min. Must be connected with 50 mm air gap to floor gully, designed for flow of 3 l/sec. 6. Condensation outlet 7. Detergent connection 8. Detergent probe 9. Equipotentional screw DISHWASHER WTM200 – FEED FROM RIGHT NOTE!...

DISHWASHER WTM200 WTM200 – FEED FROM LEFT Pre-wash module (600mm) Dishwasher, washing module Dishwasher, rinse module Condenser unit/ESD - if ordered Drying zone – optional Specification – electrically heated models Capacity/h 1st speed/2ndspeed Model wash tank Water flow litres/h Loading kW (excl.optionals) Voltage * Wash pump/ duo rinse pump/pre-wash * Other voltages available on request OPTIONAL EXTRAS: Model Drying zone ADT 900– feed from left, see below Drying zone ADT 900– feed from righ, see below Drain kit for Modular + Compact rack type 1. Drain outlet 1 1/2" M 2. Pair of marine legs...

7-252 Subject to changes without notice. Subject to changes without notice.