*mynauticexpo

Catalogs
Livorsi Marine
Platinum Series Controls

Platinum Series Controls

Product catalog summary

Introduction
This document provides installation instructions for Livorsi Marine's Plantinum Series marine engine controls. The controls come with a one-year warranty and are constructed from aluminum and stainless steel for durability. Proper installation using the provided components is crucial to maintain the warranty.

Required Tools

Phillips screwdriver
7/16" wrench or socket
3/16" Allen wrench

Installation Instructions
General Installation

Use the included 4 O-rings and 4 stainless steel wood screws for installation to avoid voiding the warranty.
Apply grease to screw holes to prevent damage to the chrome finish.

Adjusting Detent and Friction

Adjust tension by turning the Allen screw at the base of the handle using a 3/16” Allen wrench.
Periodic lubrication of rubber boots with Teflon-based lubricant is recommended.

Electronic Control Instructions

The throttle is controlled by a 0-5 volt potentiometer, programmable to customer specifications.
Ensure the control is labeled for the forward direction and do not reverse it.
Single switch function wiring: Red = +12 vdc, Green = Down, Blue = Up.

Hybrid Control Instructions

For hybrid controls, use 33C series cables.
Install new cables by routing them as old cables are removed.
Secure cables using the provided hardware and "U" bracket.
Use the included O-rings and screws for installation, applying grease to screws.

Warnings and Notes

Ensure cables are adjusted before operating engines.
Two mounting points are available for adjusting different cable throws.

Diagrams and Cutouts
The document includes exploded views of mechanical and electric throttles, along with detailed cutout dimensions for various handle configurations.

Catalog excerpts

715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 Plantinum Series Control Installation Instructions Standard, Billet and Arched handles Thank you for choosing Livorsi Marine® controls. Your new marine engine controls feature a one year warranty and are built using aluminum and stainless steel to insure years of trouble free service. The included 4 O-rings, and 4 stainless steel wood screws MUST be used to install the control or it will void the warranty. Do not over tighten. Its best to use grease in screw holes to prevent breaking chrome finish. To install your controls the following tools are needed: * Phillips screwdriver * 7/16" wrench or socket * 3/16" Allen wrench Cutouts are available at the end of this packet. Adjusting detent and friction: Adjust detent and friction to desired tension by turning allen screw at base of handle. Place throttle arm and/or detent in the slightly forward position. Using a 3/16” allen wrench, reach through the black rubber to the 3/16” set screw. Tighten or loosen as needed. Periodic lubrication of rubber boots in needed. Teflon base lubricant works best. Plantinum Series Installation Instructions

Open the catalog to page 1

715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 Plantinum Series Control Installation Instructions- Full Electronic Control Single Switch function associated with highlighted harness. Red = +12 vdc Green = Down Blue = Up Deutsch plug connects to the engine’s controller FORWARD Throttle controlled by 0-5 volt potentiometer programmable to customer’s specifications. Control will be labeled for forward direction, DO NOT reverse. Shift lever in reverse position will close highlighted circuit. Plantinum Series Installation Instructions

Open the catalog to page 2

715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 Plantinum Series Control Installation Instructions- Full Electronic Control Shift lever in Neutral position will close highlighted circuit. Shift lever in Forward position will close highlighted circuit. Plantinum Series Installation Instructions

Open the catalog to page 3

715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 Plantinum Series Control Installation Instructions- Hybrid (Electric/Mechanical) For Livorsi Hybrid Plantinum Series controls where either the throttle is electronic and shift is mechanical or vice versa, the use of 33C series cables are needed. 1. When installing new controls it is suggested to use new cables. When removing old cables, attach new cables and route as you remove old cables. 2. After connecting cables to engine and transmission, connect cables to controls using hardware provided. Screw end clevis on cable. Remove...

Open the catalog to page 4

715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 Mechanical throttle Exploded view Plantinum Series Installation Instructions

Open the catalog to page 5

Electric throttle Exploded view Plantinum Series Installation Instructions 715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415

Open the catalog to page 6

Mechanical Units Require 8.5" Clearance Below Top Deck Electrical Units Reguire 6.5" Clearance Below Top Deck

Open the catalog to page 7

9/64" PILOT HOLE FOR #10 SCREW (4)

Open the catalog to page 8

Mechanical Units Require 8.5" Clearance Below Top Deck Electrical Units Reguire 6.5" Clearance Below Top Deck

Open the catalog to page 9

Llvorsl Marine, Incf * Hvorsl.com Mechanical Units Require 8.5" Clearance Below Top Deck Electrical Units Require 6.5" Clearance Below Top Deck

Open the catalog to page 10

All Livorsi Marine catalogs and brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list