S-1200 Electric Reel
12Pages

{{requestButtons}}

Catalog excerpts

S-1200 Electric Reel - 1

Lindgren-Pitman LP S-1200 12-Volt Electric Fishing Reel Instruction and Maintenance Thank you for purchasing the finest electric reel available. Please read this instruction manual in its entirety before operating the reel. The L/P S-1200 is an investment that if taken care of, should provide many years of fishing.

Open the catalog to page 1
S-1200 Electric Reel - 2

Typical 12-Volt Outboard Boat Setup Power Requirement and Wiring: 12-volts DC Max 30Amps Plug – Hubbell #HBL328DCP Available Receptacle – Hubbell #328DCR Use a minimum of 8 gauge or thicker tinned wire between the battery and receptacle with a 30 amp resettable breaker or 50 amp slow blow fuse on the positive side as close to the battery as possible. A Hi-Amp Buss swing arm breaker with a manual trip push button is available from you local marine store or from Lindgren-Pitman. The red wire is the positive, the black is the negative. PLEASE NOTE: do not shorten the length of the reels cord –...

Open the catalog to page 2
S-1200 Electric Reel - 3

FROM S-1200 ELETRIC REEL ALL (4) WIRES MUST BE CONNECTED BOTH RED WIRES POSITIVE BOTH BLACK WIRES NEGATIVE BLUE SEAS SYSTEMS CIRCUIT BREAKER Deep Cycle Marine Auxiliary Battery utilizing

Open the catalog to page 3
S-1200 Electric Reel - 4

24-Volt Large Inboard Boat Wiring Option 60 Amp Vanner Voltmaster 66-60 (one per reel)

Open the catalog to page 4
S-1200 Electric Reel - 5

Mounting: The S-1200 weighs approximately 20 pounds with an empty spool. Please take into account the load requirements that your rod holders can handle. We recommend that at the very minimum your existing holders should be bracketed to the gunnel. LindgrenPitman, Inc. manufactures an optional rod holder bracket suitable for mounting this reel. As with any reel be sure it is tethered to the boat in case it breaks free from the rod holder, a hole is provided in base clamps to facilitate this. The S-1200 is supplied with L/P reel base clamps shown above (the rod and rod butt are shown for...

Open the catalog to page 5
S-1200 Electric Reel - 6

Loading the Spool: Typically the line of choice will be preloaded by the retailer. If not already done, it can be easily accomplished with a 12-volt DC power source such as a standard automotive battery. WARNING: never use a battery charger to run the S-1200 as the power is not clean and it can damage the circuitry and void your warranty. Because of the materials used, the nylon or titanium spools do not require backing. When loading the spool it is necessary to use the level winder to establish the correct track for the line. Once it has been fully loaded the level winder will always...

Open the catalog to page 6
S-1200 Electric Reel - 7

CONTROL PANNEL BUTTONS Reset Button This button zeros the counter. The “stop at zero” feature uses this as the reference point to turn the reel off. WARNING: Never push the reset button without first setting the rig at least 20 feet below the top of the pole. Failure to do this could cause the fishing rig to retrieve past the tip and the possible loss of gear and fish. Manual Retrieve Buttons Pushing either one of the “man” buttons turns the reel on as long as the button is held down. Once the button is released the spool stops. This is used to advance the reel manually. This is especially...

Open the catalog to page 7
S-1200 Electric Reel - 8

Hi-Low 2-Speed Button The S-1200 can operate in two speed settings, hi and low. This is done by pushing the hilow button while the reel is running. Typically the reel will spend the majority of the time in high speed. The low speed is used under heavy loads as it cuts the amperage draw and makes for less slipping of the drag. It is also useful as the counter approaches zero to slow the gear down. Harness Lugs: The top of the control panel incorporates two harness lugs that allow the angler to secure the reel to their choice of harness. Using the S-1200: Once the wiring has been routed and...

Open the catalog to page 8
S-1200 Electric Reel - 9

replacing the Allen screws that they have a good coating of anti-seize compound such as “Teff Gel” to prevent corrosion and make future changes easy. Follow the procedure for line alignment with the level winder under the “Loading the Spool” section above. S-1200 Features:  High Power “state-of-the-art” 12-VDC motor operation  Electronic control and switching.  Backlit electronic counter  Stop at zero mode  Simple easy to use controls  Hands off hauling  Gear driven level winder  Ergonomic cantilever design  Optional titanium spool endures any type or size of fishing line  Hard...

Open the catalog to page 9
S-1200 Electric Reel - 10

Maintenance: Treat the S-1200 the same as you would of any other high quality marine electronic component. While the S-1200 is completely sealed care should be taken to minimize its exposure to the salt water environment. If possible, remove the reel from the rod holders when not in use. Always rinse the reel with fresh water and thoroughly dry. The case is made from aluminum and is hard anodized to prevent corrosion, it does not require any special care beyond that noted. The nylon and titanium spools will not react with any type of line used and require no maintenance. The display bezel...

Open the catalog to page 10
S-1200 Electric Reel - 11

Warranty: The S-1200 is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Lindgren-Pitman, Inc. will, at its sole option, repair or replace any component which failed in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to abuse, misuse, accident or unauthorized alterations or repairs. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN...

Open the catalog to page 11
S-1200 Electric Reel - 12

The S-1200 is protected by Both Domestic and Foreign Patents Pending Manufactured in the U.S.A Lindgren-Pitman, Inc. 2615 N.E. 5th Avenue Pompano Beach, FL 33486 Phone (954) 943-4243 Fax (954) 943-7877 Email: sales@lindgren-pitman.com www.lindgren-pitman.com

Open the catalog to page 12

All Lindgren-Pitman catalogs and brochures

Archived catalogs