LA36
40Pages

LINAKSJ LINAK.COM/TECHLINE WE IMPROVE YOUR LIFE

LA36 The actuator LA36 is one of the most solid and powerful LINAK actuators, designed to operate under extreme conditions. The LA36 is a maintenance-free product with a long lifetime and a high IP degree. This high-quality actuator offers a very strong alternative to hydraulic solutions. TEGRATED CONTROLLER This TECHLINE® actuator comes with IC - Integrated controller. For more information on our IC options, please see: www.linak.com/techline Features: • 12, 24 or 36 V DC Permanent magnetic motor (IC only 12/24 V DC) • Thrust from 500 N - 10,000 N depending on gear ratio and spindle pitch...

Actuator with:

Permanent magnet motor 12, 24, or 36V DC* Motor: 2 x 14 AWG PVC cable Control: 6 x 20 AWG PVC cable ** Gear ratio: 6 different gear ratios available in steel (500 N, 1,700/2,600 N, 4,500 N, and 6,800/10,000 N) Slip clutch: Mechanical overload protection through an integrated slip clutch Integrated brake ensures a high self-locking ability. The brake is deactivated when the actuator is powered in order to obtain a high efficiency Hand crank: As a standard feature the actuator can be operated manually The housing is made of casted aluminium, coated for outdoor use and in harsh conditions...

Technical specifications * The typical values can have a variation of ± 20% on the current values and ± 10% on the speed values. Measurements are made with an actuator in connection with a stable power supply and an ambient temperature at 20°C. ** There are limitations on the stroke length if you need full load, please see " LA36 Load v. Stroke Length" *** Fully loaded actuators need a soft start in order to prevent the clutch from slipping when starting (see speed and current curves). Self locking ability To ensure maximum self-locking ability, please be sure that the motor is shorted when...

LA36 Load versus stroke length N.B. LA36 500 - 1.700 N is with 20 mm LA36 500 - 6.800 N is with 12 mm LA36 500 - 10.000 N is with 8 mm spindle pitch spindle pitch spindle pitch For applications that only operate in pull the limitations are 999 mm stroke and 10,000 N load. Safety factor 2. Stroke and built-in tolerances

When STROKE <300 = Built-in dimension: 200+STROKE LENGTH When STROKE >300 = Built-in dimension: 250+STROKE LENGTH _ Keep a clearance when mounting a bracket 1 When mounting a custom bracket on the moving part of the actuator, please observe the minimum clearance between bracket and cylinder top, when fully retracted, to avoid jamming and destruction of actuator drive train. A SEE DETAIL SEEDETAIL A A DETAIL SEE DETAIL AA Cable conduits for an LA36 IECEx/ATEX actuator must be ordered separately, if needed. C To order a cable conduits kit, please choose one of the following item numbers: Item...

Built-in dimensions Piston rod Back fixture Back fixture

LA36 Piston Rod Eyes When ordering AISI (304 and up) piston rod eye and back fixture, stainless steel screws are automatically included. Option “0” AISI 303 Option “1” Free cutting steel galvanised surface Option “2” Free cutting steel galvanised surface Option “5” Free cutting steel galvanised

LA36 Piston Rod Eyes Option “A” AISI 304 Option “C” 10KN = Max. load 6800 N in pull AISI 304 The Piston Rod Eye is only allowed to turn 0 - 90 degrees.

Option “1” and “2” Free cutting steel galvanised surface Option “3” and “4” Free cutting steel galvanised surface

Option “7” and “8” Free cutting steel galvanised surface

LA36 Back fixture orientation

Manual hand crank The manual hand crank can be used in the case of power failure. The cover over the Allen Key socket must be unscrewed before the Allen Key can be inserted and the Hand Crank operated. Hand Crank Torque: 6-8 Nm Hand Crank rpm: Max. 65 Piston Rod movement per turn The power supply has to be disconnected during manual operation. If the actuator is operated as a Hand crank, it must only be operated by hand, otherwise there is a potential risk of overloading and hereby damaging the actuator. Cable dimensions Y-cable dimensions: Brown: Blue: Violet: Black: Red: Brown: Blue:...

Cable dimensions Power cable dimensions: Ø 2.0mm AWG*:14mm Ø 2.0mm AWG :14mm *AWG: American Wire Gauge Signal cable dimensions: Violet: Black: Red: Yellow: Green: White: Violet: Black: Red: Yellow: Green: White:

Speed and current curves - 12V motor The values below are typical values and made with a stable power supply and an ambient temperature of 20°C. All measurements above describe the spindle pitch (e.g. 20mm) and the gear type (e.g. E gear) of the actuator. Speed and current are based on a nominal power supply of 12, 24, 36VDC. When ordering LA36F When purchasing the LA36 actuator with fast gear and slide for the end-stop function, the customer has been informed that there is an increased risk that the activation arm for end-stop can be damaged during use, especially if the actuator runs to...

Speed and current curves - 24V motor The values below are typical values and made with a stable power supply and an ambient temperature of 20°C. LA36 24V motor speed vs. load All measurements above describe the spindle pitch (e.g. 20mm) and the gear type (e.g. E gear) of the actuator. Speed and current are based on a nominal power supply of 12, 24, 36VDC. When ordering LA36F When purchasing the LA36 actuator with fast gear and slide for the end-stop function, the customer has been informed that there is an increased risk that the activation arm for end-stop can be damaged during use,...

Speed and current curves - 36V motor The values below are typical values and made with a stable power supply and an ambient temperature of 20°C. LA36 36V motor speed vs. load All measurements above describe the spindle pitch (e.g. 20mm) and the gear type (e.g. E gear) of the actuator. When ordering LA36F When purchasing the LA36 actuator with fast gear and slide for the end-stop function, the customer has been informed that there is an increased risk that the activation arm for end-stop can be damaged during use, especially if the actuator runs to limit switch without load, both in the...