SeaQuest
5Pages

{{requestButtons}}

Catalog excerpts

SeaQuest - 1

Technical Data Sheet Approved silicone resin based FRC SeaQuest Product description This is a three component fouling release coating based on elastotain technology. It is biocide free and provides excellent fouling protection and hull performance. This is achieved by a smooth, low friction surface reducing hull deterioration and speed loss. To be used as finish coat in immersed environments. Suitable on approved Jotun FRC tiecoats only. Typical use Marine: Recommended for underwater hull in newbuilding and drydocking. Specially designed as a premium solution for vessels trading at medium to high speed or activity. It has high gloss and excellent colour stability providing long term aesthetics appearance. Specially suitable for specific trades and where the focus is long term hull protection. The product is suitable for long service periods and can be used up to 60 months as a part of a complete coating system. Protective: Specially designed for offshore constructions and outside hull for static installations. Typical trade Designed for both global and coastal trade. Other Colours red, grey, black, blue Product data Property Solids by volume Flash point calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) IED (2010/75/EU) (theoretical) GB/T 23985-2009 (tested) Korea Clean Air Conservation Act (tested) (Max. thinning ratio included) VOC-US/Hong Kong VOC-EU VOC-China VOC-Korea The provided data is typical for factory produced products, subject to slight variation depending on colour. All data is valid for mixed paint. This Technical Data Sheet supersedes those previously issued. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Open the catalog to page 1
SeaQuest - 2

Technical Data Sheet SeaQuest Film thickness per coat Typical recommended specification range Dry film thickness Theoretical spreading rate Surface preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Surface preparation summary table Surface preparation Substrate Minimum Clean, dry and undamaged compatible coating Coated surfaces Recommended Clean, dry and undamaged compatible coating Application Application methods The product can be applied by Spray: Use airless spray. Care should be taken to avoid overspray...

Open the catalog to page 2
SeaQuest - 3

Technical Data Sheet SeaQuest Thinner/Cleaning solvent Do not add thinner. Cleaning solvent: When thinners are used as a cleaning solvent, the use must be in accordance with prevailing local regulations. Guiding data for airless spray Nozzle tip (inch/1000): Pressure at nozzle (minimum): Drying and Curing time Substrate temperature Surface (touch) dry Dried/cured for immersion For maximum overcoating intervals, refer to the Application Guide (AG) for this product. After finished application the substrate temperature must be kept at minimum 10 °C for at least 2 hours. Lowest substrate...

Open the catalog to page 3
SeaQuest - 4

Technical Data Sheet SeaQuest Volume SeaQuest Comp B SeaQuest Comp C The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Storage The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf life at 23 °C SeaQuest Comp A SeaQuest Comp B In some markets commercial shelf life can be dictated shorter by local legislation. The above is...

Open the catalog to page 4
SeaQuest - 5

Technical Data Sheet SeaQuest The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical experience. Jotun's products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the given data without further notice. Users should always consult Jotun for specific guidance on the general...

Open the catalog to page 5

All JOTUN catalogs and brochures

  1. Megafiller

    5 Pages

  2. Hardtop XP

    6 Pages

  3. SeaForce 30

    5 Pages

  4. SeaForce 60

    5 Pages

  5. SeaForce 90

    5 Pages

  6. Pioner

    4 Pages

  7. Jota Armour

    5 Pages

  8. Penguard FC

    5 Pages

  9. Pilot II

    5 Pages

  10. Tankguard DW

    6 Pages

  11. AntiPest

    5 Pages

  12. Racing

    3 Pages

  13. Megafiller

    5 Pages

  14. Osmoshell

    4 Pages

  15. MegaGloss HG

    5 Pages

  16. TopGloss

    5 Pages

  17. Megacote

    5 Pages

  18. Megasealer

    5 Pages

  19. SeaMate M

    4 Pages

  20. Hardtop AX

    5 Pages

  21. EasyPrimer

    4 Pages

  22. Marathon IQ2

    5 Pages

  23. Hardtop One

    9 Pages

  24. Alkydprimer

    5 Pages

  25. EasyGloss

    3 Pages

  26. Aluflex

    3 Pages

  27. JOTAMASTIC

    20 Pages