SeaForce 60 M
5Pages

{{requestButtons}}

Catalog excerpts

SeaForce 60 M - 1

Technical Data Sheet Approved SeaForce 60 M Product description This is a one component high solids hydrolysing antifouling coating based on ion exchange technology. It provides very good fouling protection. This is achieved by self polishing characteristics reducing hull deterioration. To be used as finish coat in immersed environments only. Suitable on approved primers and tie coats on aluminium and carbon steel substrates. It can be applied at sub zero surface temperatures. Typical use Marine: Recommended for under water hull in drydocking. Designed for vessels trading at a wide range of speed and activity. The product can be used for long service periods up to 60 months as a part of a complete coating system. Typical trade Suited for vessels operating in global service. Recommended for deep sea trade. Antifouling. Approvals and certificates Compliant with IMO Antifouling System Convention AFS/CONF/26. Additional certificates and approvals may be available on request. Product data Property Solids by volume Flash point Density ISO 3233 ISO 3679 Method 1 calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) IED (2010/75/EU) (theoretical) VOC-US/Hong Kong VOC-EU VOC-China VOC-Korea GB/T 23985-2009 (tested) Korea Clean Air Conservation Act (tested) (Max. thinning ratio included) The provided data is typical for factory produced products, subject to slight variation depending on colour. This Technical Data Sheet supersedes those previously issued. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Open the catalog to page 1
SeaForce 60 M - 2

Technical Data Sheet SeaForce 60 M Film thickness per coat Typical recommended specification range Dry film thickness Theoretical spreading rate Max total DFT for multiple coats in the antifouling system: 500 µm Surface preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Surface preparation summary table Surface preparation Substrate Coated surfaces New tie coat or new antifouling: Remove any contamination that could interfere with the intercoat adhesion. Exceeding maximum recoat intervals will require...

Open the catalog to page 2
SeaForce 60 M - 3

Technical Data Sheet SeaForce 60 M Product mixing Single pack Thinner/Cleaning solvent Thinner: Guiding data for airless spray Nozzle tip (inch/1000): Pressure at nozzle (minimum): Drying and Curing time Substrate temperature Surface (touch) dry Dry to over coat, minimum For maximum overcoating intervals, refer to the Application Guide (AG) for this product. When three or more antifouling coats are applied in rapid succession it is recommended to double the time for immersion. Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at...

Open the catalog to page 3
SeaForce 60 M - 4

Technical Data Sheet SeaForce 60 M SeaForce 60 M The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Storage The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf life at 23 °C SeaForce 60 M In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint...

Open the catalog to page 4
SeaForce 60 M - 5

Technical Data Sheet SeaForce 60 M If there is any inconsistency between different language issues of this document, the English (United Kingdom) version will prevail. This Technical Data Sheet supersedes those previously issued. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Open the catalog to page 5

All JOTUN catalogs and brochures

  1. Megafiller

    5 Pages

  2. Hardtop XP

    6 Pages

  3. SeaForce 30

    5 Pages

  4. SeaForce 60

    5 Pages

  5. SeaForce 90

    5 Pages

  6. Pioner

    4 Pages

  7. Jota Armour

    5 Pages

  8. Penguard FC

    5 Pages

  9. Pilot II

    5 Pages

  10. Tankguard DW

    6 Pages

  11. AntiPest

    5 Pages

  12. Racing

    3 Pages

  13. Megafiller

    5 Pages

  14. Osmoshell

    4 Pages

  15. MegaGloss HG

    5 Pages

  16. TopGloss

    5 Pages

  17. Megacote

    5 Pages

  18. Megasealer

    5 Pages

  19. SeaMate M

    4 Pages

  20. Hardtop AX

    5 Pages

  21. EasyPrimer

    4 Pages

  22. Marathon IQ2

    5 Pages

  23. SeaQuest

    5 Pages

  24. Hardtop One

    9 Pages

  25. Alkydprimer

    5 Pages

  26. EasyGloss

    3 Pages

  27. Aluflex

    3 Pages

  28. JOTAMASTIC

    20 Pages