Jotaprime 510
5Pages

{{requestButtons}}

Catalog excerpts

Jotaprime 510 - 1

Technical Data Sheet Approved phenolic/novolac epoxy Jotaprime 510 Product description This is a two component polyamine cured pure epoxy coating. It is a fast drying, abrasion resistant, high solids, high build product. Designed as a universal, all round, all year, new building coating where fast dry to handle is required. Can be used as primer, mid coat or finish coat in atmospheric and immersed environments. Suitable for properly prepared aluminium, carbon steel, galvanised steel, shop primed steel and stainless steel substrate. It can be applied at sub zero surface temperatures. Typical use Marine: Exterior and interior areas, including water ballast tanks, crude oil tanks, outside hulls, superstructures, decks and cargo holds. Approved for PSPC cross over testing with a wide range of shop primers. Other Approvals and certificates Approved for PSPC for Water Ballast Tanks according to IMO Res. MSC 215(82) Approved for PSPC for Crude Oil Tanks according to IMO Res. MSC 288(87) When used as part of an approved scheme, this material has the following certification: - Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8 Consult your Jotun representative for details. Additional certificates and approvals may be available on request. Colours aluminium, aluminium red toned, grey, grey XO, red Product data Property Gloss level (GU 60 °) Flash point Density ISO 2813 ISO 3679 Method 1 calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) IED (2010/75/EU) (theoretical) GB/T 23985-2009 (tested) VOC-US/Hong Kong VOC-EU VOC-China The provided data is typical for factory produced products, subject to slight variation depending on colour. All data is valid for mixed paint. Gloss description: According to Jotun Performance Coatings' definition. This Technical Data Sheet supersedes those previously issued. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Open the catalog to page 1
Jotaprime 510 - 2

Technical Data Sheet Jotaprime 510 Film thickness per coat Typical recommended specification range Dry film thickness Theoretical spreading rate Surface preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Surface preparation summary table Surface preparation Substrate Carbon steel Stainless steel The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface. Abrasive blast cleaning to achieve a surface profile...

Open the catalog to page 2
Jotaprime 510 - 3

Technical Data Sheet Jotaprime 510 Roller: May be used for small areas. Not recommended for first primer coat. Care must be taken to achieve the specified dry film thickness. Product mixing ratio (by volume) Jotaprime 510 Comp A Jotaprime 510 Comp B Thinner/Cleaning solvent Thinner: Guiding data for airless spray Nozzle tip (inch/1000): Pressure at nozzle (minimum): Drying and Curing time Substrate temperature Surface (touch) dry Walk-on-dry Dry to over coat, minimum Dried/cured for immersion For maximum overcoating intervals, refer to the Application Guide (AG) for this product. Drying and...

Open the catalog to page 3
Jotaprime 510 - 4

Technical Data Sheet Jotaprime 510 Induction time and Pot life Paint temperature Induction time Pot life Heat resistance Temperature Continuous Dry, atmospheric Peak temperature duration max. 1 hour. The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures. Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in...

Open the catalog to page 4
Jotaprime 510 - 5

Technical Data Sheet Jotaprime 510 Shelf life at 23 °C Jotaprime 510 Comp A Jotaprime 510 Comp B In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection. Caution This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation. Applicators and operators shall use appropriate personal protection equipment...

Open the catalog to page 5

All JOTUN catalogs and brochures

  1. Megafiller

    5 Pages

  2. Hardtop XP

    6 Pages

  3. SeaForce 30

    5 Pages

  4. SeaForce 60

    5 Pages

  5. SeaForce 90

    5 Pages

  6. Pioner

    4 Pages

  7. Jota Armour

    5 Pages

  8. Penguard FC

    5 Pages

  9. Pilot II

    5 Pages

  10. Tankguard DW

    6 Pages

  11. AntiPest

    5 Pages

  12. Racing

    3 Pages

  13. Megafiller

    5 Pages

  14. Osmoshell

    4 Pages

  15. MegaGloss HG

    5 Pages

  16. TopGloss

    5 Pages

  17. Megacote

    5 Pages

  18. Megasealer

    5 Pages

  19. SeaMate M

    4 Pages

  20. Hardtop AX

    5 Pages

  21. EasyPrimer

    4 Pages

  22. Marathon IQ2

    5 Pages

  23. SeaQuest

    5 Pages

  24. Hardtop One

    9 Pages

  25. Alkydprimer

    5 Pages

  26. EasyGloss

    3 Pages

  27. Aluflex

    3 Pages

  28. JOTAMASTIC

    20 Pages