Jota Armour
5Pages

{{requestButtons}}

Catalog excerpts

Jota Armour - 1

Technical Data Sheet Approved Jota Armour Product description This is a three component abrasion resistant polyamine cured epoxy coating. Specially designed as an anti-skid coating. Suitable on metallic substrates coated with approved primers and on concrete coated with suitable sealer. Typical use Can be used on helidecks, walkways, ramps, weigh bridge decks, decks in general where abrasion resistance and non-slip properties are required. Other Approvals and certificates Approved to UK Defence Standard 80-134/1 for the Royal Navy, flight decks, hangar decks and weather decks Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 4, suitable for decks and walkways. Additional certificates and approvals may be available on request. Colours grey 038, green 137, BS 640 Product data Property STANDARD GRADE Solids by volume Gloss level (GU 60 °) Flash point Density VOC-EU VOC-China VOC-Korea IED (2010/75/EU) (theoretical) GB/T 23985-2009 (ISO 11890-1) (tested) Korea Clean Air Conservation Act (tested) WINTER GRADE Solids by volume Flash point Density The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to Jotun Performance Coatings' definition. This Technical Data Sheet supersedes those previously issued. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Open the catalog to page 1
Jota Armour - 2

Technical Data Sheet Jota Armour Film thickness per coat Typical recommended specification range STANDARD GRADE Dry film thickness Theoretical spreading rate WINTER GRADE Dry film thickness Wet film thickness Theoretical spreading rate Anti-slip roughness profile of coating limits accuracy on film thickness measurements. Approximate spreading rate for 1000 μm dry film is 8 m²/kit from practical testing. Surface preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Surface preparation summary table Surface...

Open the catalog to page 2
Jota Armour - 3

Technical Data Sheet Jota Armour Thinner/Cleaning solvent Thinner: Drying and Curing time Substrate temperature STANDARD GRADE Surface (touch) dry Walk-on-dry Dry to over coat, minimum Dried/cured for service WINTER GRADE Surface (touch) dry Dry to over coat, minimum Dried/cured for service For maximum overcoating intervals, refer to the Application Guide (AG) for this product. Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product. Surface (touch) dry: The state of drying when slight pressure...

Open the catalog to page 3
Jota Armour - 4

Technical Data Sheet Jota Armour Heat resistance Temperature Continuous Dry, atmospheric Peak temperature duration max. 1 hour. The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures. Product compatibility Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system recommendation. Previous coat: epoxy, epoxy mastic, zinc epoxy Subsequent coat: epoxy, epoxy mastic, polyurethane Packaging...

Open the catalog to page 4
Jota Armour - 5

Technical Data Sheet Jota Armour Caution This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the...

Open the catalog to page 5

All JOTUN catalogs and brochures

  1. Megafiller

    5 Pages

  2. Hardtop XP

    6 Pages

  3. SeaForce 30

    5 Pages

  4. SeaForce 60

    5 Pages

  5. SeaForce 90

    5 Pages

  6. Pioner

    4 Pages

  7. Penguard FC

    5 Pages

  8. Pilot II

    5 Pages

  9. Tankguard DW

    6 Pages

  10. AntiPest

    5 Pages

  11. Racing

    3 Pages

  12. Megafiller

    5 Pages

  13. Osmoshell

    4 Pages

  14. MegaGloss HG

    5 Pages

  15. TopGloss

    5 Pages

  16. Megacote

    5 Pages

  17. Megasealer

    5 Pages

  18. SeaMate M

    4 Pages

  19. Hardtop AX

    5 Pages

  20. EasyPrimer

    4 Pages

  21. Marathon IQ2

    5 Pages

  22. SeaQuest

    5 Pages

  23. Hardtop One

    9 Pages

  24. Alkydprimer

    5 Pages

  25. EasyGloss

    3 Pages

  26. Aluflex

    3 Pages

  27. JOTAMASTIC

    20 Pages