Trilux 33 Antifouling High Performance Brightly Coloured Antifouling PRODUCT DESCRIPTION Reformulated to give improved protection and a brighter white, Trilux 33 is a high performance brightly coloured antifouling. Formulated with Biolux Technology®, the slow polishing formula helps avoid paint build up and gives effective fouling protection for up to 18 months. Suitable for all types of construction, including aluminium, Trilux 33 now has a lower VOC content that helps reduce environmental solvent emissions. * Suitable for all substrates including aluminium and bronze. * Suitable for propellers and boottops. PRODUCT INFORMATION Colour YBA064White, YBA065Navy, YBA067Black , YBA069Red , YBA070Green , YBA071Blue, YBA072Grey Not all colours or pack sizes are available in all countries. Specific Gravity Volume Solids Typical Shelf Life Unit Size DRYING/OVERCOATING INFORMATION Drying 5°C (41°F) Note: Maximum immersion time is 6 months at all temperatures. If maximum immersion time is exceeded, high pressure water wash or wet abrade with 180240 grade paper prior to immersion. MAJOR REFURBISHMENT The first coat of Trilux 33 should always be applied over a recommended primer system. The primer surface should be dry and free of all contaminants (oil, grease, salt etc) and overcoated with Trilux 33 within the overcoating interval specified for the primer. REPAIR and UPGRADING APPROVED SYSTEMS Degrease the surface. Clean the entire area with controlled high pressure washing (3000 psi./211 bar). Repair corroded areas with the recommended anticorrosive primer system (Primocon). PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet. BARE GRP Gelshield 200 for osmosis protection, or Primocon. STEEL/IRON Prime with Interprotect or Primocon. LEAD Prime with Interprotect or Primocon. WOOD Prime with Interprotect or Primocon. ALUMINIUM/ALLOY Prime with Interprotect or Primocon. Ensure the area is clean and dry. Apply Trilux 33 within the overcoating intervals specified by the primer. Apply an extra stripe coat in areas of high wear such as chines, rudders, sterngear and any leading edges. Note: Maximum time to immersion is 6 months. If coating is left for more than 6 months, the surface should be high pressure fresh water washed or wet abraded using 180240 grade paper prior to immersion. Mixing Stir well before use. Thinner Thinner No.3 Thinning Thinning is not recommended. Use in exceptional circumstances only. For example, extremes of weather. Cleaner Thinner No.3 Airless Spray Pressure: 176210 bar. Tip Size: 2180. For Professional use ONLY. Other Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness. It is important for performance to apply the correct thickness. Some Important Points If Trilux 33 is exposed for any period of time, e.g. over the winter, it must be high pressure fresh water washed before being immersed. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Please refer to your local representative or visit www.yachtpaint.com for further information. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. © AkzoNobel 2019. Substrate temperature should be 3°C/5°F above dew point and maximum 35°C

washed or wet abraded using 180240 grade paper prior to immersion. Hints Trilux 33 Antifouling High Performance Brightly Mixing Stir well before use. Thinner Thinner No.3 Thinning Thinning is not recommended. Use in exceptional circumstances only. For example, extremes of weather. Cleaner Thinner No.3 Airless Spray Pressure: 176210 bar. Tip Size: 2180. For Professional use ONLY. Other Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance Coloured Antifouling to apply the correct thickness. It is important for performance to apply...