
Catalog excerpts

Epoxy Finishing Fairing Compound Interfill 833 is an Epoxy Finishing Filler designed for professional use. Interfill 833 is available in both standard and fast cure versions, to provide maximum flexibility for application in a variety of conditions. With the availability Even in cooler conditions you’ll be able to apply an epoxy primer such as Interprime 820 much sooner than the traditional standard cure Finishing Fillers. A standard curing agent is available for conditions where a longer pot-life and set up time is required. Key features and benefits Easy to apply and sand Interfill 833 is available in both standard and fast cure versions, to provide maximum flexibility for application in a variety of conditions When the fast curing agent is used at temperatures around 23oC / 73oF the filler can be overcoated as soon as it is sandable (i.e. after 6 hours) Interfill 830 can fill up to 2cm in one coat, without the risk of sagging / slumping Fine grade extenders give extra smooth results Contrasting colour (Green) to Interfill 830 Profiling Filler (Grey) Applicator friendly: simple 1:1 mix ratio Interfill 833 should be applied over cured, sanded epoxy fillers such as Interfill 830 or on GRP / Composite PRODUCT DATA Area Base Converter / Curing Agent Methods of Application Available Shades Pack Size Mix Ratio Typical Shelf Life Above and below the waterline YAA813 YAA814 – Standard, YAA815 - Fast Trowel or Batten YAA813 - Green 2.5LT – Base + 2.5LT – C/A = 5LT mixed, also 60LT 1:1 2 Years Refer to the relevant datasheet for more information on yachtpaint.com Always read the Health & Safety precautions on the label prior to use
Open the catalog to page 1
Surface preparations and systems Previously painted surface in good condition : Wash down with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Sweep blast or abrade with 180– 280 grade paper. Poor surface condition : All previous coatings should be removed back to solid material and filled with Interfill® 830. Intefill 830 : Sand with 60-120grade (grit) paper. Bare GRP / Composite : Sand with 120-180 grade paper. Remove all sanding residue using a clean air line and sweeping with a clean brush or broom. For the best results, vacuum clean. Typical scheme – For reference...
Open the catalog to page 2All International Yacht Paint catalogs and brochures
-
Epiglass HT9000 Standard
2 Pages
-
Interprotect
2 Pages
-
Liquid Rubbing
2 Pages
-
Cruiser 200
2 Pages
-
Boatguard 100
2 Pages
-
Interstrip AF
1 Pages
-
Gelshield 200
2 Pages
-
Watertite
2 Pages
-
Super Cleaner
2 Pages
-
Original
2 Pages
-
Trilux 33
2 Pages
-
Trilux Prop-O-Drev
2 Pages
-
VC 17m Extra
2 Pages
-
Perfection Undercoat
2 Pages
-
Interdeck
2 Pages
-
Danboline
2 Pages
-
Yacht Primer
2 Pages
-
Woodskin
2 Pages
-
VC Offshore EU
2 Pages
-
Perfection Plus
2 Pages
-
Goldspar Satin
2 Pages
-
Compass
2 Pages
-
Schooner
2 Pages
-
Pre-Kote
2 Pages
-
Thinner No. 9
1 Pages
-
Thinner No.7
1 Pages
-
Matting Additive
2 Pages
-
VC Tar2
2 Pages
-
Primocon
2 Pages
-
Perfection
2 Pages
-
Interprime 820
2 Pages
-
Interfill 830
2 Pages
-
Super Gloss HS
2 Pages
-
Cruiser Uno EU
2 Pages
-
Toplac
2 Pages
-
Micron Extra
2 Pages
-
Micron 66
2 Pages
-
Interspeed Ultra
2 Pages
-
Interprime 450
2 Pages
-
Gelshield Plus
2 Pages
Archived catalogs
-
Fibreglass Surface Prep
2 Pages