Interdeck
1 / 2Pages

Interdeck Finishes Slip Resistant Deck Paint PRODUCT DESCRIPTION Interdeck provides an excellent slip resistant finish. It contains a fine aggregate and will apply easily on all substrates. * Low sheen finish prevents dazzling reflected sunlight off decks * Easy application * Available in a range of colours The tough polyurethane resin protects decks against everyday wear and tear. PRODUCT INFORMATION Colour YJB000White, YJB923Squall Blue, YJC089Cream, YJF684Grey, YJG009Sand Beige Not all colours or pack sizes are available in all countries. Semi Gloss Specific Gravity Volume Solids Typical Shelf Life Unit Size DRYING/OVERCOATING INFORMATION Drying 5°C (41°F) PREVIOUSLY PAINTED SURFACES In Good Condition Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280320 grade (grit) paper. In Poor Condition Remove all previous coatings and prime the substrate. PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet. BARE WOOD Sand smooth with 80180 grade paper and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems). STEEL Degrease with solvent or suitable detergent cleaner. Gritblast to Sa 2½ near white metal surface. If gritblasting is not possible, grind the metal surface with 2436 grit abrasive discs to a uniform, clean, bright metal surface with a 50 75 microns anchor pattern. Use angle grinder on small areas. Clean thoroughly and allow to dry. Preprime using an International primer as detailed for specific coating systems. ALUMINIUM Degrease with solvent or suitable detergent cleaner. Sand well using 24120 grade (aluminium compatible) paper. Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Preprime using an International primer as soon as possible (within 8 hours) as detailed for specific coating systems. GRP Degrease with solvent or suitable detergent cleaner. Sand well using 60120 grade paper. Clean thoroughly and allow to dry. Preprime using an International primer as detailed for specific coating systems. AGED/WEATHERED GELCOATS Due to the potentially porous nature of aged/weathered gelcoats the risk of solvent/moisture entrapment after painting is much higher than when gelcoat is new. As a result this entrapment could lead to blistering of the paint film. To reduce the risk of paint film blistering it is recommended that 3 coats of Interprotect are applied to seal the gelcoat. Interprotect must be overcoated with Perfection Undercoat prior to topcoat application. ALL SUBSTRATES If any filling is required use the appropriate product from the International range . Sand the primer with 180220 grade wet or dry paper. Remove dust with a dust wipe. Apply 12 coats. Mixing Stir well before use. Thinner YTA800 Thinners No.1 Cleaner Thinners No.1 Ventilation and Humidity Control Apply in dry, well ventilated conditions. Other For best results either stipple by brush or use a mohair roller. Some Important Points Formulated for exterior use. Please refer to your local representative or visit www.yachtpaint.com for further information. Product temperature should be minimum 10°C/50°F and maximum 30°C/86°F. All trademarks

Finishes Hints Slip Resistant Deck Paint AGED/WEATHERED GELCOATS Due to the potentially porous nature of aged/weathered gelcoats the risk of solvent/moisture entrapment after painting is much higher than when gelcoat is new. As a result this entrapment could lead to blistering of the paint film. To reduce the risk of paint film blistering it is recommended that 3 coats of Interprotect are applied to seal the gelcoat. Interprotect must be overcoated with Perfection Undercoat prior to topcoat application. ALL SUBSTRATES If any filling is required use the appropriate product from the...