Catalogs >
International Yacht Paint >
Goldspar Satin

Goldspar Satin
1 / 2Pages

Catalog excerpts

Goldspar Satin Varnishes Quick Drying Satin Yacht Varnish PRODUCT DESCRIPTION Goldspar Satin is a onecomponent interior satin varnish that is quick drying which helps to reduce dust pick up. This traditional varnish provides a hard smooth satin finish which is resistant to mild acids & alkalis. PRODUCT INFORMATION Colour Specific Gravity Volume Solids Typical Shelf Life Unit Size DRYING/OVERCOATING INFORMATION Drying 5°C (41°F) 5°C (41°F) Overcoated By Goldspar Satin PREVIOUSLY VARNISHED WOOD In Good Condition Clean with thinners. Sand smooth with 280320 grade paper. Remove sanding dust with thinners. In Poor Condition Remove all previous coatings. BARE WOOD Ensure that the surface is thoroughly degreased. Sand smooth with 80180 grade paper and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying the first coat. Priming bare wood: Thin the first coat by 1015% with Thinner No.1. Apply a minimum of 3 unthinned coats, more if using a roller. Avoid using direct from the can. Pour the amount you expect to use in a separate container. Mixing Stir well before use. Thinner Thinner No.1, Thinner No.3 Cleaner Thinner No.1 Airless Spray (Professional spray application only) Pressure: 176210 bar. Tip Size: 13651580. Conventional Spray (Professional spray application only) Pressure: 23 bar. Tip Size: 1.11.4 mm. Thin 2530% with Thinners No.3 Roller If applying by roller, lay off with a brush or pad otherwise air bubbles may become trapped in the film. Other For Airmix spray application: Pressure: 2 bar. Tip Size: 06113. For best results sand lightly between coats with 320400 grade paper. Avoid using direct from the can. Pour the amount you expect to use in a separate container. Some Important Points Only use recommended thinners. Use above the waterline only. Avoid painting in direct sunlight. Product temperature should be minimum 15°C and maximum 35°C. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Suitable for use on all types of wood as long as correct surface preparation has been carried out. (Theoretical) 11.5 m²/L per coat (Practical) 10.3 m²/L per coat Application Methods Brush, Roller, Airmix, Airless Spray, Conventional Spray (Professional spray application only) TRANSPORTATION, STORAGE AND SAFETY INFORMATION Storage to your local representative or visit www.yachtpaint.com for further information. GENERAL INFORMATION: Please refer Exposure to air and extremes of temperature should be avoided. For the full shelf life of Goldspar Satin to be realised All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. © AkzoNo

Open the catalog to page 1

(Theoretical) 11.5 m²/L per coat (Practical) 10.3 m²/L per coat Goldspar Satin Application Methods Brush, Roller, Airmix, Airless Spray, Conventional Spray (Professional spray application only) Quick Drying Satin Yacht Varnish TRANSPORTATION, STORAGE AND SAFETY INFORMATION Storage GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Goldspar Satin to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight. TRANSPORTATION: Goldspar Satin...

Open the catalog to page 2