Group: AkzoNobel
Catalog excerpts
Danboline Finishes Bilge Protection Paint PRODUCT DESCRIPTION Danboline protects bilges, lockers and bulkheads against moisture penetration and wear and tear. Danboline will resist oil and fuel spillage and cleans easily. * High opacity for excellent covering power * Hard wearing * Available in a range of colours PRODUCT INFORMATION Colour YMA100Grey, YMA102White Not all colours or pack sizes are available in all countries. Specific Gravity Volume Solids Typical Shelf Life Unit Size DRYING/OVERCOATING INFORMATION Drying 5°C (41°F) PREVIOUSLY PAINTED SURFACES In Good Condition Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 180280 grade paper. In Poor Condition Remove all previous coatings and prime the substrate. PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet. BARE WOOD Prime with Yacht Primer or Interprotect. STEEL Prime with Yacht Primer or Interprotect. ALUMINIUM Prime with Yacht Primer or Interprotect. GRP Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 180220 grade paper. Particular attention should be given to the reverse side of moulded GRP. No priming necessary. Sand the primer using 180280 grade wet or dry paper. Remove dust with a dust wipe. Apply 12 coats. Mixing Stir well before use. Thinner Thinner No.1 (Thinner 910 for spraying) Cleaner Thinners No.1 Ventilation and Humidity Control Apply in dry, well ventilated conditions. Conventional Spray Pressure: 34 bar. Tip Size: 1.2 mm. Thin approximately 20% with Thinners 910. SPRAY APPLICATION PROFESSIONAL APPLICATORS ONLY. Other For added protection against moisture absorption and osmosis in the bilges, use Gelshield products. Some Important Points Product temperature should be minimum 15°C and maximum 35°C. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Suitable for all substrates specified. Only overcoat with onepack paints. (Theoretical) 12.3 m²/L per coat by brush (Practical) 11.0 m²/L per coat Application Methods Brush, Conventional Spray, Roller Please refer to your local representative or visit www.yachtpaint.com for further information. All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. © AkzoNobel 2019. TRANSPORTATION, STORAGE AND SAFETY INFORMATION Storage Ref:3307 Danboline
Open the catalog to page 1Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Compatibility/Substrates Suitable for all substrates specified. Only overcoat with onepack paints. (Theoretical) 12.3 m²/L per coat by brush (Practical) 11.0 m²/L per coat Recommended DFT per coat Bilge Protection Paint Application Methods Brush, Conventional Spray, Roller TRANSPORTATION, STORAGE AND SAFETY INFORMATION Storage GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Danboline to be...
Open the catalog to page 2All International Yacht Paint catalogs and brochures
-
Epiglass HT9000 Standard
2 Pages
-
Interprotect
2 Pages
-
Liquid Rubbing
2 Pages
-
Cruiser 200
2 Pages
-
Boatguard 100
2 Pages
-
Interstrip AF
1 Pages
-
Gelshield 200
2 Pages
-
Watertite
2 Pages
-
Super Cleaner
2 Pages
-
Original
2 Pages
-
Trilux 33
2 Pages
-
Trilux Prop-O-Drev
2 Pages
-
VC 17m Extra
2 Pages
-
Perfection Undercoat
2 Pages
-
Interdeck
2 Pages
-
Yacht Primer
2 Pages
-
Woodskin
2 Pages
-
VC Offshore EU
2 Pages
-
Perfection Plus
2 Pages
-
Goldspar Satin
2 Pages
-
Compass
2 Pages
-
Schooner
2 Pages
-
Pre-Kote
2 Pages
-
Thinner No. 9
1 Pages
-
Thinner No.7
1 Pages
-
Matting Additive
2 Pages
-
VC Tar2
2 Pages
-
Primocon
2 Pages
-
Perfection
2 Pages
-
Interprime 820
2 Pages
-
Interfill 833
2 Pages
-
Interfill 830
2 Pages
-
Super Gloss HS
2 Pages
-
Cruiser Uno EU
2 Pages
-
Toplac
2 Pages
-
Micron Extra
2 Pages
-
Micron 66
2 Pages
-
Interspeed Ultra
2 Pages
-
Interprime 450
2 Pages
-
Gelshield Plus
2 Pages
-
Fibreglass Surface Prep
2 Pages