INTERTHANE 990 DATA SHEET
4Pages

{{requestButtons}}

Catalog excerpts

INTERTHANE 990 DATA SHEET - 1

Polyurethane Finish PRODUCT DESCRIPTION A two pack, acrylic polyurethane finish giving excellent durability and long term recoatability. INTENDED USES PRODUCT INFORMATION As a cosmetic finish on above water areas. Suitable for use on topsides, external superstructure, external decks and For use at Newbuilding, Maintenance & Repair or On Board Maintenance. Part B (Curing Agent) Volume Solids Typical Film Thickness Theoretical Coverage Flash Point Induction Period PHBOOO-White, PHY999-Black ; and a wide range of colors. High Gloss 6.00 volume(s) Part A to 1 volume(s) Part B 457 ft2/US gal at 2 mils dft, allow appropriate loss factors Airless Spray, Brush, Conventional Spray, Roller Part A 93°F; Part B 120°F; Mixed 95°F Drying Information REGULATORY DATA Overcoating Data - see limitations Substrate Temperature Note Drying and overcoating times quoted are measured at 2 mils dry, at higher film thickness times will be increased. 420 g/lt (3.50 lb/US gal) as supplied (EPA Method 24) 341 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. MIL-PRF-24667B, Type I, II, III & VIII Composition G MIL-PRF-24667B, Type I, V, VII & Vili, Composition L for color marking puposes Marine Coatings

Open the catalog to page 1
INTERTHANE 990 DATA SHEET - 2

Polyurethane Finish When used as part of an approved scheme, this material has the following certification: • Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16)) • Fire Resistance - MSC61 (67) Smoke & Toxicity (WFR) • NORSOK M-501, Rev 4, system no.1 (IMITISI) • Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. Interthane 990 must be applied over a recommended primer system, which will vary depending upon the vessel area. Direct application is acceptable over the following marine anticorrosives: A...

Open the catalog to page 2
INTERTHANE 990 DATA SHEET - 3

Polyurethane Finish Airless Spray Conventional Spray Work Stoppages and Cleanup Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. Not recommended. Use International GTA056, GTA713, GTA733 only in exceptional circumstances. DO NOT USE ANY OTHER THINNER. DO NOT thin more than allowed by local environmental legislation Total output fluid pressure at spray tip not less than 2200 psi...

Open the catalog to page 3
INTERTHANE 990 DATA SHEET - 4

Polyurethane Finish This product is not recommended for use in permanantly immersed conditions. Interthane 990 may be used on boottop areas at reduced overcoating intervals over appropriate primers. Consult International Paint. For brush and roller application, and in some colors, two coats of Interthane 990 may be required to give uniform coverage, especially when applying Interthane 990 over dark undercoats and when using certain lead-free bright finish colors such as yellows and oranges. Best practice is to use a color compatible intermediate or anticorrosive coating under Interthane...

Open the catalog to page 4

All International Marine catalogs and brochures

  1. Fisheries

    2 Pages

  2. Intersleek

    6 Pages

  3. Cargo Hold

    8 Pages

  4. Colour Card

    2 Pages

  5. Intertuf 362

    4 Pages

Archived catalogs