Catalogs >
International Marine >
Interswift 455FB

Interswift 455FB
4Pages

Catalog excerpts

Interswift 455FB TBT Free Antifouling PRODUCT DESCRIPTION TBT free, self polishing antifouling system incorporating unique Copper Acrylate SPC (Self Polishing Copolymer) technology. INTENDED USES Especially designed for the protection of flat bottom areas only. For use at Newbuilding and Maintenance & Repair. PRODUCT INFORMATION Colour BBA004-Dark Red, BBA008-Brown Finish/Sheen Not applicable Part B (Curing Agent) Not applicable Volume Solids 58% ±2% (ISO 3233:1998) Mix Ratio Not applicable Typical Film Thickness Range: 75 - 200 microns dry (129 - 345 microns wet) may be specified depending upon end use. Theoretical Coverage Range: 7.7 - 2.9 m²/litre at 75 - 200 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point Single Pack 27°C Drying Information 5°C 10°C 25°C 35°C Touch Dry [ISO 9117/3:2010] 4.5 hrs 4 hrs 2 hrs 1.5 hrs Before Flooding 24 hrs 24 hrs 12 hrs 12 hrs 5°C 10°C Overcoating Data - see limitations Substrate Temperature 25°C 35°C Overcoated By Max Min Max Min Max Min Max Interswift 455FB REGULATORY DATA Min 12 hrs 3 mths 10 hrs 3 mths 6 hrs 3 mths 4 hrs 3 mths VOC 384 g/lt as supplied (EPA Method 24) 210 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:23/08/2011 Ref:2929

Open the catalog to page 1

Interswift 455FB TBT Free Antifouling CERTIFICATION When used as part of an approved scheme, this material has the following certification: • • • • • Bureau Veritas Germanischer Lloyd Det Norske Veritas Lloyds Register Korean Register of Shipping Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from...

Open the catalog to page 2

Airless Spray Conventional Spray This material is a one pack coating and should always be mixed thoroughly with a power agitator before Not recommended. Use International GTA007 only in exceptional circumstances and as advised by the International Paint Technical Service representative. DO NOT thin more than allowed by local environmental Total output fluid pressure at spray tip not less than 176 kg/cm2 (2500 p.s.i.) Application by conventional spray is not recommended. Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film...

Open the catalog to page 3

Interswift 455FB TBT Free Antifouling LIMITATIONS UNIT SIZE FOR FLAT BOTTOM USE ONLY If the following maximum recommended exposure times before flooding are exceeded, antifouling performance may be impaired: Tropical conditions - 3 months Temperate conditions - 6 months If these times are exceeded, close high pressure fresh water wash (at 3,000 p.s.i., 211 kg/cm²) the surface before immersion. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative...

Open the catalog to page 4