Interspeed 340 TBT Free CDP Antifouling PRODUCT DESCRIPTION TBT free, controlled depletion polymer (CDP) self polishing antifouling system. INTENDED USES For direct application over existing antifoulings in good condition. Can be applied over BQA341 where specified. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION Colour BQA344-Plum, BQA346-Pink, BQA347-Red Finish/Sheen Not applicable Part B (Curing Agent) Not applicable Volume Solids 60% ±2% (ISO 3233:1998) Mix Ratio Not applicable Typical Film Thickness 125 microns dry (208 microns wet) Theoretical Coverage 4.80 m²/litre at 125 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point Single Pack 26°C Drying Information 5°C 10°C Touch Dry [ISO 1517:73] 4 hrs Before Flooding 24 hrs 35°C 3.5 hrs 2 hrs 60 mins 20 hrs 5°C 10°C Overcoating Data - see limitations 25°C 12 hrs 12 hrs Substrate Temperature 25°C 35°C Overcoated By Min Max Min Max Min Max Min Max Interspeed 340 12 hrs 6 mths 10 hrs 6 mths 6 hrs 6 mths 4 hrs 3 mths Note REGULATORY DATA Overcoating data refers to BQA344/7 followed by BQA344/7. VOC 352 g/lt as supplied (EPA Method 24) 191 g/kg (Top Coat) of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:23/07/2010 Ref:2755

Interspeed 340 TBT Free CDP Antifouling CERTIFICATION When used as part of an approved scheme, this material has the following certification: Product recognised by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • • • • Lloyds Register Germanischer Lloyd Korean Register of Shipping Det Norske Veritas Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be...

Interspeed 340 TBT Free CDP Antifouling APPLICATION Mixing This material is a one pack coating and should always be mixed thoroughly with a power agitator before application. Thinner Not recommended. Use International GTA007 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.66-0.79 mm (26-31 thou) Total output fluid pressure at spray tip not less than 176 kg/cm² (2500 p.s.i.) Conventional Spray Application by conventional spray is not recommended. Brush Application by brush is recommended for small areas...

Interspeed 340 TBT Free CDP Antifouling LIMITATIONS If the following maximum recommended exposure times before flooding are exceeded, antifouling performance may be impaired: Interspeed 340 BQA344/347 - Temperate conditions - 6 months, Tropical conditions - 3 months On immersion Interspeed 340 lightens in colour. On exposure all colours of Interspeed 340 may darken in colour, depending upon exposure period and climatic conditions. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local...