Interplate Zero
4Pages

{{requestButtons}}

Catalog excerpts

Interplate Zero - 1

Interplate Zero Water Based Inorganic Shop Primer PRODUCT DESCRIPTION A two pack, heat resistant, water based shop (pre-construction) primer providing good corrosion protection and resistance to damage caused by welding, gas cutting and fairing. Suitable for fast welding processes and offers control of secondary surface preparation requirements. INTENDED USES As a shop (pre-construction) primer for the protection of steel during fabrication and assembly. Suitable for use with controlled cathodic protection. For use at Newbuilding. PRODUCT INFORMATION ZER010/ZER011-Grey, other colors available upon request Part B (Curing Agent) Volume Solids 5.34 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness Theoretical Coverage 962 ft²/US gal at 0.6 mils dft, allow appropriate loss factors Airless Spray, Brush, Conventional Spray, Roller Flash Point Drying Information (a) It is recommended to pre-heat the steel to 86-95°Fprior to applying Interplate Zero. After application, it is also recommended to post-cure Interplate Zero to 86-95°F for 15 seconds minimum. (b) At higher than specified film thickness or under application conditions of high humidity, a minimum steel temperature of 104°F is recommended. Overcoating Data - see limitations Substrate Temperature Note REGULATORY DATA Consult International Paint, minimum of 7 days for appropriate primers. 0 g/lt (0.00 lb/US gal) calculated 0 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:7/6/201

Open the catalog to page 1
Interplate Zero - 2

Interplate Zero Water Based Inorganic Shop Primer CERTIFICATION When used as part of an approved scheme, this material has the following certification: • • • • • Weld Quality - Approval of Prefabrication Primers (LR) Weld Quality - Shop Primers for Corrosion Protection of Steel Plates and Structures (DNV) Fire Resistance - Surface Spread of Flame (Exova Warringtonfire) Fire Resistance - Smoke & Toxicity (Exova Warringtonfire) Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your...

Open the catalog to page 2
Interplate Zero - 3

Interplate Zero Water Based Inorganic Shop Primer APPLICATION Mixing Material is supplied in 2 separate containers as a unit. Always mix a complete unit in the proportions supplied.Agitate the binder (Part A) with a power agitator then slowly add the powder (Part B) whilst continuing agitating.Where product is supplied as a 4.7 US Gallon unit it will be necessary to transfer Part A to a separate suitable container prior to adding Part B.Allow to mix for at least 5 minutes, sieve through a 30-60 mesh screen before use. Continue stirring during use. Always add Powder to Binder. Not...

Open the catalog to page 3
Interplate Zero - 4

Interplate Zero Water Based Inorganic Shop Primer LIMITATIONS Drying times will depend on the substrate temperature and ventilation conditions. If the relative humidity is below 50%, cure will be retarded. Interplate Zero is not recommended for manual spray application. At higher dry film thickness, fabrication properties (welding and cutting) may be affected. Shop primers are not recommended for use as touch-up primers after fabrication. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult...

Open the catalog to page 4

All International Marine catalogs and brochures

  1. Fisheries

    2 Pages

  2. Intersleek

    6 Pages

  3. Cargo Hold

    8 Pages

  4. Colour Card

    2 Pages

  5. Intertuf 362

    4 Pages

  6. INTERLAC 678

    4 Pages

Archived catalogs