Interline 644


Catalog excerpts

Interline 644 - 1

Interline 644 Epoxy Phenolic PRODUCT DESCRIPTION A light coloured, solvent free, tar free, two pack epoxy phenolic cargo tank coating. INTENDED USES A high performance, solvent free coating system for fuel carriage, crude oil and white oil carriage and for use in potable water tanks. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION Part B (Curing Agent) Volume Solids 4 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness 7 mils dry (7.4 mils wet) For additional scheme information refer to the Interline 644 Application Guideline Theoretical Coverage 218 ft²/US gal at 7 mils dft, allow appropriate loss factors Plural Feed Airless Spray, Airless Spray, Brush, Roller Flash Point Part A 181°F; Part B 230°F; Mixed 181°F Induction Period Drying Information Pot life at a temperature of 50°F is for information only. Recommended mixed paint temperature prior to application is 77°F minimum. See also Mixing information on page 2. Overcoating Data - see limitations Substrate Temperature REGULATORY DATA 98 g/lt (0.82 lb/US gal) as supplied (EPA Method 24) 110 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:8/1/

Open the catalog to page 1
Interline 644 - 2

Interline 644 Epoxy Phenolic SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. NEWBUILDING/MAJOR REFURBISHMENT Abrasive blast clean to Sa2½ (ISO...

Open the catalog to page 2
Interline 644 - 3

Interline 644 Epoxy Phenolic APPLICATION Mixing For information on mixing see page 2. Airless Spray Ensure spray gun is rated beyond the maximum fluid outlet pressure of the pump to be used. Single Feed - Tip range 0.015" - 0.021" (381-530 microns). Smaller tip gives better film thickness control - Total output fluid pressure at spray tip not less than 5000 p.s.i. (352 kg/cm²) - Pump Ratio 70:1 It is recommended that an in-line heater is installed as close to the pump fluid outlet as possible. This will allow the operator to use heat to improve flow of material through long paint hoses. The...

Open the catalog to page 3
Interline 644 - 4

Interline 644 Epoxy Phenolic LIMITATIONS UNIT SIZE At ambient temperatures below 77°F paint lines must be lagged. This product will not cure adequately below 50°F. The drying times and overcoating intervals may alter due to various on-site factors such as tank configuration and ventilation rates. Consult your International Paint representative for the time interval required between coating completion and first cargo loading. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local...

Open the catalog to page 4

All International Marine catalogs and brochures

  1. Fisheries

    2 Pages

  2. Intersleek

    6 Pages

  3. Cargo Hold

    8 Pages

  4. Colour Card

    2 Pages

  5. Intertuf 362

    4 Pages

  6. INTERLAC 678

    4 Pages

Archived catalogs