*mynauticexpo

Intergard 5000

Product catalog summary

Product Description: A light-colored, tar-free, surface-tolerant, two-pack epoxy coating with high volume solids (82%). It is designed for use in water ballast tanks, cofferdams, void spaces, wet spaces, bilges, and crude oil tanks. The product complies with IMO Resolution MSC.215 (82) for newbuildings.

Intended Uses: The coating system includes KBA501-Aluminium as the first coat and KBA502-Buff as the second coat. It is applied using airless spray, brush, or roller, with a mix ratio of 4 parts A to 1 part B.

Product Information: Theoretical coverage is 5.12 m²/litre at 160 microns dft. The flash point for Part A is 32°C, Part B is 58°C, and mixed is 33°C. The system requires two coats at 160 microns dry per coat.

Drying Information: Touch dry times range from 2 hours at 35°C to 15 hours at 5°C. Hard dry times range from 4 hours at 35°C to 34 hours at 5°C. Minimum time before ballasting is 12 hours at 35°C to 3 days at 5°C.

Regulatory Data: VOC values are 220 g/lt as supplied and 152 g/kg of liquid paint as supplied, compliant with the EU Solvent Emissions Directive.

Certification: Certified for use over specific International Paint Shop Primers and compliant with various international marine standards.

Surface Preparations: Surfaces must be clean, dry, and free from contamination. Specific standards for cleanliness and preparation are outlined, including ISO and SSPC standards.

Application: Mixing involves combining Part A and Part B thoroughly. Airless spray is recommended for full coats, while brush and roller are suitable for small areas. Proper ventilation and humidity control are necessary during application.

Safety: Compliance with health, safety, and environmental standards is required. Proper protective equipment and ventilation are necessary during application.

Limitations: Environmental factors such as temperature and humidity must be considered. The product has a shelf life of 12 months at 25°C.

Storage: Store in dry, shaded conditions away from heat and ignition sources. The product is manufactured in the United Kingdom and Saudi Arabia.

Important Note: Users should verify the current data sheet version and consult local representatives for specific recommendations.

Catalog excerpts

Intergard 5000 IMO Resolution MSC.215 (82) compliant Ballast Tank Coating PRODUCT DESCRIPTION A light coloured, tar free, surface tolerant, two pack epoxy coating with high volume solids (82%). INTENDED USES A high performance epoxy coating for use in water ballast tanks, cofferdams, void spaces, wet spaces, bilges and crude oil tanks. Is type approved as complying with the requirements of IMO Resolution MSC.215 (82) for use on newbuildings. PRODUCT INFORMATION Colour System Film Thickness KBA501-Aluminium, First Coat KBA502-Buff, Second Coat 2 coats at 160 microns dry (195 microns wet) per coat Part B (Curing Agent) Volume Solids 4 volume(s) Part A to 1 volume(s) Part B Specific Gravity Base (Part A) 1.719-1.811 Curing Agent (Part B) 0.965-1.015 Mixed Paint 1.57-1.65 Theoretical Coverage 5.12 m²/litre at 160 microns dft, allow appropriate loss factors Airless Spray, Brush, Roller Flash Point (Typical) Part A 32°C; Part B 58°C; Mixed 33°C Drying Information Walk-on Time Minimum time before ballasting Overcoating Data - see limitations Intergard 5000 Full coat over full coat Intergard 5000 Full coat over stripe coat REGULATORY DATA 220 g/lt as supplied (EPA Method 24) 152 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:04/07/2016 Ref:4234

Open the catalog to page 1

Intergard 5000 IMO Resolution MSC.215 (82) compliant Ballast Tank Coating CERTIFICATION IMO PSPC Resolution MSC.215 (82) - Registro Italiano Navale (RINA) IMO PSPC Resolution MSC.215 (82) - American Bureau of Shipping (ABS) IMO PSPC Resolution MSC.215 (82) - Bureau Veritas (BV) IMO PSPC Resolution MSC.215 (82) - Det Norske Veritas (DNV) IMO PSPC Resolution MSC.215 (82) - Lloyds Register (LR) Shop Primers Intergard 5000 is certified for use over the following International Paint Shop Primers: • • • • • Interplate Zero Interplate 805 Interplate 855 Interplate 937 Interplate 997 International Paint...

Open the catalog to page 2

Intergard 5000 IMO Resolution MSC.215 (82) compliant Ballast Tank Coating APPLICATION Mixing Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. Ventilation and Humidity Control After application of the final coat of the system, ventilation should be continued for a minimum period of 48 hours unless otherwise...

Open the catalog to page 3

Intergard 5000 IMO Resolution MSC.215 (82) compliant Ballast Tank Coating LIMITATIONS Intergard 5000 should be high pressure fresh water washed and/or solvent washed prior to overcoating, where necessary, to ensure removal of any surface contamination that has accumulated. The curing agent for Intergard 5000 has a tendency to go cloudy when stored at temperatures below 5°C. Warming the curing agent above 5°C will restore the clear nature of the product. No adverse effect on performance is observed if the curing agent is cloudy when used. Film Thickness Minimum Film Thickness : The specified scheme...

Open the catalog to page 4

Intergard 5000

Intergard 5000

Catalog excerpts

All International Marine catalogs and brochures

Archived catalogs