Intergard 269


Catalog excerpts

Intergard 269 - 1

Intergard 269 Epoxy Primer/ Tie Coat PRODUCT DESCRIPTION A quick drying two pack epoxy holding primer / tie coat which is suitable for overcoating after extended periods of weathering. INTENDED USES For use as a primer for the protection of prepared steel prior to the application of a wide range of products. Can also be used as a tie coat for application to freshly applied zinc primers to prevent zinc salt formation on weathering and to reduce pinholing of subsequent applied coatings. Suitable for use with controlled cathodic protection. For use at Newbuilding, Maintenance & Repair or On Board Maintenance. PRODUCT INFORMATION Part B (Curing Agent) Volume Solids 4.00 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness Theoretical Coverage 471 ft²/US gal at 1.6 mils dft, allow appropriate loss factors Airless Spray, Brush, Conventional Spray, Roller Flash Point Part A 79°F; Part B 77°F; Mixed 79°F Induction Period Drying Information Overcoating Data - see limitations Substrate Temperature REGULATORY DATA Overcoating information for all other Intergard, Intertuf, Interbond and Interprime products refer to Intertuf 262 above. 450 g/lt (3.76 lb/US gal) as supplied (EPA Method 24) 293 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) 3.50 g/lt Chinese National Standard GB23985 Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:2/8/20

Open the catalog to page 1
Intergard 269 - 2

Intergard 269 Epoxy Primer/ Tie Coat CERTIFICATION When used as part of an approved scheme, this material has the following certification: • Food Contact - Carriage of Grain (NOHH) • Fire Resistance - Surface Spread of Flame (Exova Warringtonfire) • Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should...

Open the catalog to page 2
Intergard 269 - 3

Intergard 269 Epoxy Primer/ Tie Coat APPLICATION Mixing Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. International GTA220. Thinning is not normally required. Consult the local representative for advice during application in extreme conditions. Do not thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 15-21 thou (0.38-0.53 mm) Total...

Open the catalog to page 3
Intergard 269 - 4

Intergard 269 Epoxy Primer/ Tie Coat LIMITATIONS UNIT SIZE This product will not cure adequately below 41°F. For maximum performance, the curing temperature should be above 50°F. The history and age of the steel and the method of working can have a significant effect on the paint consumption. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be...

Open the catalog to page 4

All International Marine catalogs and brochures

  1. Fisheries

    2 Pages

  2. Intersleek

    6 Pages

  3. Cargo Hold

    8 Pages

  4. Colour Card

    2 Pages

  5. Intertuf 362

    4 Pages

  6. INTERLAC 678

    4 Pages

Archived catalogs