Catalogs >
International Marine >
Intercept 8000 LPP

Intercept 8000 LPP
4Pages

Catalog excerpts

Intercept 8000 LPP TBT Free, Low Friction, Linear Polishing Polymer PRODUCT DESCRIPTION A high performance, low friction, linear polishing polymer (LPP) antifouling incorporating unique patented Lubyon ® technology. INTENDED USES Specifically designed for Deep Sea Vessels. For use at Newbuilding and Maintenance & Repair. PRODUCT INFORMATION LPP814-Brown, LPP817-Red Note: The above codes will be substituted by LPP824-Brown and LPP827-Red when supplied from Felling and Dammam manufacturing locations. Not applicable Volume Solids Typical Film Thickness Range: 75 - 200 microns dry (132 - 351 microns wet) may be specified depending upon end use. Theoretical Coverage Range: 7.6 - 2.9 m²/litre at 75 - 200 microns dft, allow appropriate loss factors Airless Spray, Brush, Roller Flash Point (Typical) Drying Information Before Flooding Single Coat Before Flooding Multiple Coats Note If the antifouling scheme includes any coat greater than 150 microns, and/or is greater than 300 microns in total at major refurbishment or repair, the time to flooding must be increased to 48 hours at temperatures of 10°C or less, 36 hours at 25°C and 24 hours at 35°C. For flooding of Intercept 7000 / 8000 LPP duplex schemes follow multiple coat Intercept 8000 LPP flooding times. Overcoating Data - see limitations Substrate Temperature REGULATORY DATA 378 g/lt as supplied (EPA Method 24) 203 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:19/02/2013 Ref:10086

Open the catalog to page 1

Intercept 8000 LPP TBT Free, Low Friction, Linear Polishing Polymer CERTIFICATION When used as part of an approved scheme, this product has the following certification: Product recognised by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • Bureau Veritas • Germanischer Lloyd Consult your International Paint representative for details. Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance...

Open the catalog to page 2

Intercept 8000 LPP TBT Free, Low Friction, Linear Polishing Polymer APPLICATION Mixing This material is a one pack coating and should always be mixed thoroughly with a power agitator before application. Not Recommended. Use International GTA007 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.54-0.8 mm (21-31 thou) Total output fluid pressure at spray tip not less than 190 kg/cm² (2700 p.s.i.) Conventional Spray Application by conventional spray is not recommended. Application by...

Open the catalog to page 3

Intercept 8000 LPP TBT Free, Low Friction, Linear Polishing Polymer LIMITATIONS UNIT SIZE Coating lifetime is directly proportional to thickness applied. Performance of the product is dependent upon the specified film thickness being achieved. On immersion, Intercept 8000 LPP will exhibit a slight colour change. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to...

Open the catalog to page 4