Interbond 201 - Temperate
4Pages

{{requestButtons}}

Catalog excerpts

Interbond 201 - Temperate - 1

Interbond 201 Epoxy Primer/Finish PRODUCT DESCRIPTION TEMPERATE A hard wearing, surface tolerant, two pack epoxy primer/finish offering corrosion protection in one coat. A low temperature version of Interbond 201 is available for use down to -5°C. INTENDED USES As an anticorrosive primer/finish for decks, deck fittings and cargo holds. For use at Maintenance & Repair or On Board Maintenance. PRODUCT INFORMATION Part B (Curing Agent) Volume Solids 4.00 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness Theoretical Coverage 4.93 m²/litre at 150 microns dft, allow appropriate loss factors Airless Spray, Brush, Roller Flash Point (Typical) Part A 28°C;Part B 34°C;Mixed 29°C (Product produced and supplied in North America has flash points of Part A 43°C , Part B 39°C and Mixed 39°C respectively due to locally sourced solvents. There is no detrimental effect on product performance.) Induction Period 30 minutes at temperatures below 25°C for KDA100 Drying Information Overcoating Data - see limitations Substrate Temperature Interbond 201 Ballast Holds Interbond 501 REGULATORY DATA Stated figures for pot life, drying times and overcoating intervals are for temperate product. For low temperature product data see separate data sheet. 279 g/lt as supplied (EPA Method 24) 229 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:12/12/2014 Ref:430

Open the catalog to page 1
Interbond 201 - Temperate - 2

Interbond 201 Epoxy Primer/Finish CERTIFICATION When used as part of an approved scheme, this material has the following certification: • • • • Food Contact - Carriage of Grain (NOHA) Food Contact - FDA Compliant: Dry Foodstuffs Fire Resistance - Surface Spread of Flame (Exova Warringtonfire) Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be protected. When using in cargo holds, consult the Interbond 201...

Open the catalog to page 2
Interbond 201 - Temperate - 3

Interbond 201 Epoxy Primer/Finish APPLICATION Mixing Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. Not recommended. Use International GTA220 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.53-0.84 mm (21-33 thou) Total output fluid pressure at spray tip not less than 176 - 246 kg/cm²...

Open the catalog to page 3
Interbond 201 - Temperate - 4

Interbond 201 Epoxy Primer/Finish LIMITATIONS UNIT SIZE When spraying large areas, application of a brush coat is recommended over pitted or rough surfaces to ensure full penetration. Stripe coating of complex structures is recommended. Interbond 201 low temperature grade is not suitable for use in Ballast Holds. Optimum performance is achieved when Interbond 201 is applied over blasted steel. In common with all epoxy based coatings Interbond 201 will exhibit chalking of the film on UV exposure. Overcoating information is given for guidance only and is subject to regional variation...

Open the catalog to page 4

All International Marine catalogs and brochures

  1. Fisheries

    2 Pages

  2. Intersleek

    6 Pages

  3. Cargo Hold

    8 Pages

  4. Colour Card

    2 Pages

  5. Intertuf 362

    4 Pages

  6. INTERLAC 678

    4 Pages

Archived catalogs