- Catalogs
- Instromet Weather Systems Ltd
- Instromet 0-10V DC Wind Speed Sensor wiring diagram
Instromet 0-10V DC Wind Speed Sensor wiring diagram
1 / 2 PagesView full catalog
Instromet 0-10V DC Wind Speed Sensor wiring diagram
Product catalog summary
Installation Instructions
Sensor Wiring: The sensor requires a three-core cable connected via a terminal block inside the sensor enclosure. Access this by removing the cover screws. A wiring color identification label is provided.
Roof Top Wind/Temperature Sensor: Mount the unit on a mast 25-50mm in diameter, positioned high and away from obstructions like chimneys and trees to avoid wind turbulence. Ideally, place it at least 2 meters above roof peaks. Secure the cable properly, avoiding proximity to power or transmitter cables. If necessary, shorten the cable when connecting to the display unit.
Troubleshooting Guide
General Issues: Ensure the power supply is connected and turned on (24V DC). Verify correct wiring of the power cable to the sensor enclosure.
Wind Speed Issues: Confirm that the anemometer cups turn freely and check the wiring, especially the blue wire from the Wind Sensor. Inspect the cable for damage.
Wind Sensor Voltages:
If issues persist, contact the service department at 01692 502800 or return the sensor for checking or replacement.
Contact Information:
Instromet Weather Systems Ltd
10a, Lyngate Industrial Estate
North Walsham, Norfolk NR28 0AJ
Tel: (01692) 502800
Fax: (01692) 502801
Email: [email protected]
Sensor Wiring: The sensor requires a three-core cable connected via a terminal block inside the sensor enclosure. Access this by removing the cover screws. A wiring color identification label is provided.
Roof Top Wind/Temperature Sensor: Mount the unit on a mast 25-50mm in diameter, positioned high and away from obstructions like chimneys and trees to avoid wind turbulence. Ideally, place it at least 2 meters above roof peaks. Secure the cable properly, avoiding proximity to power or transmitter cables. If necessary, shorten the cable when connecting to the display unit.
Troubleshooting Guide
General Issues: Ensure the power supply is connected and turned on (24V DC). Verify correct wiring of the power cable to the sensor enclosure.
Wind Speed Issues: Confirm that the anemometer cups turn freely and check the wiring, especially the blue wire from the Wind Sensor. Inspect the cable for damage.
Wind Sensor Voltages:
- Supply Voltage: Black – Red = 24V DC
- Wind Speed: Black – Blue = 0-10V DC
- 90mph equates to 8.5V DC
If issues persist, contact the service department at 01692 502800 or return the sensor for checking or replacement.
Contact Information:
Instromet Weather Systems Ltd
10a, Lyngate Industrial Estate
North Walsham, Norfolk NR28 0AJ
Tel: (01692) 502800
Fax: (01692) 502801
Email: [email protected]
See more
Catalog excerpts
Instromet 0-10V DC Wind Speed Sensor wiring diagram
Open the catalog to page 1
Installation Instructions Sensor wiring The three core cable should be connected to the individual sensor via the terminal block within the sensor enclosure. This can be accessed by un-doing the two screws securing the cover, where a wiring colour identification label will be found. Roof Top Wind/Temperature Sensor This unit should be mounted on a mast of 25-50mm (1-2inches) in diameter, as high and as far away as possible from chimneys, roof peaks, buildings, trees and transmitter aerials which may cause wind turbulence or interference. Where possible the roof top wind sensor should be mounted...
Open the catalog to page 2All Instromet Weather Systems Ltd catalogs and brochures
Kestrel 4500 measures2 Pages
Kestrel 3000 measures2 Pages
Kestrel 2000 measures2 Pages
Kestrel 1000 measures2 Pages
instromet16 Pages
Humidity2 Pages
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.