ANTIFOULING FOR FISHING BOATS

Product catalog summary

Product Description: The antifouling product is a self-polishing coating with controlled solubility, biologically active throughout its lifespan. It can be applied directly over most well-adhered antifouling coats without accumulating old layers.

Fields of Application: Suitable for submerged surfaces of primed polyester, wood, and iron.

Technical Data:

Finish: Semi-matt
Colour: Red
Density: 1.82 - 1.88 Kg/l
Coverage: 6-9 m²/l
Drying Time: 1 hour at 23ºC, 60% RH
Recoat Time: 6 hours at 23ºC, 60% RH
Application Methods: Brush and roller
Cleaning: TITAN YATE Thinner
Application Temperature: 15-40ºC, RH < 80%
Flash Point: 25 ºC
Volume Solids: 58 - 60%
Pack Sizes: 4 l and 750 ml

Directions for Use:

Stir contents before use. Ensure the surface is sanded, clean, dry, and salt-free.
Avoid painting under direct sunlight or on dewy surfaces.
Apply an additional coat in high-wear areas like the waterline and keel.

Bare Surfaces:

Polyester: Degrease and apply 2 coats of Epoxy Primer.
Metal: Apply 1 coat of Epoxy Primer, followed by 3-4 coats of M-150 Epoxy Primer.
Wood: Apply 2 coats of Epoxy Primer, thinning the first coat with 20% Thinner.
Finish with two coats of Antifouling.

Maintenance:

Good Condition: Wash and apply 2 coats of Antifouling.
Poor Condition: Remove old coats, wash, and treat as a bare surface.

Precautions: Read the label before use. Store in closed containers away from heat and below 0ºC. Shelf life is 36 months. Follow local waste regulations and avoid environmental contamination.

Additional Information: The technical sheet is valid for five years from the issue date. Quality is guaranteed, but liability is limited to the coating itself. Consult technical service if needed.

Catalog excerpts

ANTIFOULING FOR FISHING BOATS Description Self-polishing antifouling by controlled solubility. Biologically active for the whole product life. It can be directly applied on the majority of well-adhered antifouling coats. It does not cumulate old antifouling coats. Fields of Application Self-polishing antifouling for submerged surfaces of suitably primed Polyester, Wood and Iron. Technical Data Finish Equipment Cleaning TITAN YATE Thinner Pack sizes Variations in temperature, humidity, thickness, tinting or surface type, etc. may lead to changes in drying, in coverage or in other properties. Directions for use GENERAL REMARKS: Carefully stir the contents in the can before use. The surface has to be sanded, clean, dry and salt-free (wash it). Do not paint if the surface is under direct sunlight or if it has dew on it. In areas of higher wear, such as waterline, keel, rudder, etc., it is recommended an additional coat, since water turbulence speeds up self-polishing. BARE SURFACES: Polyester:Degrease with TITAN YATE Thinner and apply 2 coats of TITAN YATE Epoxy Primer in intervals of 24 hours (For osmosis prevention, apply M-150 Epoxy Primer). Metal: Apply 1 coat of TITAN YATE Epoxy Primer. After 24 hours, apply 3-4 coats of TITAN YATE M-150 Epoxy Primer, strictly following the instructions of the pack. Wood: Apply 2 coats of TITAN YATE Epoxy Primer, the 1st coat thinned with 20% TITAN YATE Thinner. In all cases, finish with two coats of TITAN YATE Antifouling.

Open the catalog to page 1

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION: Wash with fresh water jet and directly apply 2 coats of TITAN YATE Antifouling. MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION: Thoroughly remove all previous coats with TITAN Paint Stripper or TITAN YATE Water-Based Paint Stripper. Wash with fresh water and afterwards proceed as for a bare surface. Precautions Always read the pack label before use. For more information, please refer to the Safety Data Sheet. Store in tightly closed containers protected from sources of heat and temperatures below 0ºC. Shelf life: 36 months...

Open the catalog to page 2