Product Data HEMPADUR 15570 15570: BASE 15579: CURING AGENT 95570 Description: HEMPADUR 15570 is a two component, polyamide-adduct cured epoxy paint, which cures to a strong and highly corrosion resistant coating, at temperatures down to -10°C/14°F. The Micaceous Iron Oxide pigmented light grey 12430 quality is also well suited for application under humid conditions, on damp steel surfaces, and may be applied on moist surfaces Recommended use: As a maintenance and repair primer, intermediate, and/or finishing coat in HEMPADUR systems in severely corrosive environment. As a finishing coat where a cosmetic appearance is of less importance. As a low temperature curing epoxy primer, intermediate, and/or finishing coat in paint systems according to specification. Well suited as a (blast) primer in epoxy systems. Mist coat on GALVOSIL. Service temperature: Maximum, dry exposure only: 140°C/284°F Ballast water service. Resists normal ambient temperatures at sea (Avoid long-term exposure to negative temperature gradients). Other liquids. Contact HEMPEL Certificates/Approvals: Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great Britain. Approved as a low flame spread material. According to IMO resolution MSC 61 (67): Denmark, France, Spain. EC-type Examination Certificate: Denmark, France, Indonesia, Malaysia, Singapore, Spain. Complies with EU Directive 2004/42/EC: subcategory j. Availability: Part of Group Assortment. Local availability subject to confirmation. PHYSICAL CONSTANTS: Shade nos/Colours: Finish: Volume solids, %: Theoretical spreading rate: Flash point: Specific gravity: Dry to touch: Fully cured: VOC content: 12430 (MIO)* / Reddish grey Flat 54 ± 1 5.4 m2/l [216.5 sq.ft./US gallon] to 100 micron/4 mils 25 °C [77 °F] 1.4 kg/litre [11.6 lbs/US gallon] 3 to 4 approx. hour(s) 20°C/68°F 7 day(s) 20°C/68°F 414 g/l [3.4 lbs/US gallon] - The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. APPLICATION DETAILS: Version, mixed product: Mixing ratio: Application method: Thinner (max.vol.): Pot life: Nozzle orifice: Nozzle pressure: Cleaning of tools: Indicated film thickness, dry: Indicated film thickness, wet: Recoat interval, min: Recoat interval, max: Safety: 15570 BASE 15579: CURING AGENT 95570 3 : 1 by volume Airless spray / Air spray / Brush 08450 (5%) / 08450 (15%) / 08450 (5%) 2 hour(s) 20°C/68°F 0.019 to 0.021 " 175 bar [2537.5 psi] (Airless spray data are indicative and subject to adjustment) HEMPEL'S TOOL CLEANER 99610 100 micron [4 mils] see REMARKS overleaf 200 micron [8 mils] According to separate APPLICATION INSTRUCTIONS According to separate APPLICATION INSTRUCTIONS Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult HEMPEL Safety Data Sheets and follow all local or national safety regulations. Date of issue: December 2012 - Page: 1/2 Product Data Sheet

HEMPADUR 15570 SURFACE PREPARATION: New steel: Abrasive blasting to Sa 2½ (ISO 8501-1:2007). For temporary protection, if required, use a suitable shopprimer. All damage of shopprimer and contamination from storage and fabrication should be thoroughly cleaned prior to final painting. For repair and touch-up use: HEMPADUR Other metals and light alloys: Thorough degreasing and (light) abrasive sweeping to remove contamination and to secure adhesion - surface profile depending on later exposure. Stainless steel: (eg. ballast tanks of chemical carriers) to be abrasive blast cleaned to a uniform,...