Our most efficient antifouling solution

If you are searching for the ONE that will: Our best peforming antifouling with proven track record for 2 year fouling protection. Available in shades: k eep your boat fouling-free save you from re-painting every year save you money save on fuel save the environment Biocide-free solution based on silicone and hydrogel, which gives the coating surface water-like properties making it difficult for fouling organisms to attach to the hull and easy for them to be removed when the boat is in motion. Silic One is The ONE. The premium antifouling. More than 10 years of boat owners’ trust in Silic One!...

Switching to Silic One is easy.Overcoating existing antifoulingSurface preparationRemove all loose/brittle layers. Abrade. Rinse carefully with freshwater and allow the surface to dry.ApplicationApply layers of the system as indicated below: 4 easy steps: Conversion Primer Silic One Tiecoat Surface preparation 3 Conversion Primer Silic One Silic One Silic One Tiecoat Conversion Primer Silic One Tiecoat ^ Silic One To be immersed after final coat 36h 1 month 24h 1 month 24h 1 month *Apply Silic One Tiecoat as soon as previous coat of Conversion Primer is dry to touch. The Silic One Tiecoat must...

Boats without antifouling Surface preparation Clean with a suitable detergent and sand with dry abrasive paper (P120). Carefully clean with water and allow the surface to dry. Apply layers of the system as indicated below: Silic One Silic One Silic One Tiecoat Light Primer Silic One for propellersSurface preparation • Remove old antifouling first • Clean with a suitable detergent such as Hempel's Pre-Clean (for aluminium propellers make sure that Hempel’s Pre-Clean has been thinned 1:20) • Create a palpable roughness by abrading with 40 grit sand paper or other mechanical methods, preferably...

Never seen before... Hempel’s Infinity Hempel's Infinity Cleaning High speed motor boats Hempel’s Silic One is self-cleaning on motor boats. Slow speed boats & sailboats The coating can be cleaned as frequently as desired/required, thus maintaining a perfectly clean surface with extremely low friction. Revolutionary recharger for Silic One system. Hempel’s Silic One is easy to clean. You can use one of two following options: Use a high pressure, fresh water wash to clean the surface. Use a dense sponge or a cloth and then rinse with a hose. Important Do not use a hard brush, bristles or similar....

Never seen before... Hempel’s Infinity Hempel’s Infinity How to recharge the Silic One system with Hempel's Infinity Tool option 2: Roller Surface preparation Clean the underwater area with a suitable detergent such as Hempel's Pre-Clean. Rinse with freshwater. Allow to dry. 3 Allow to dry for minimum 24 hours. Tools: Long haired roller or wide brush. Application 1 Mix the Infinity product thoroughly and pour into the tray. 2 Apply Infinity to the whole underwater surface. Application stroke direction is not relevant as long as the entire underwater surface is covered. Tool option 1: Brush 4...

Never seen before... >/ Less costs >/ More free time Less painting v More sailing HEMPEL infinity Less is more. Still not using Silic One system? More than 10 years of boat owners’ trust in Silic One! @ HEMPEL Trust is earned

FAQ Is Silic One more expensive than traditional antifouling? No, first time application cost is higher but over the years, cost is massively reduced due to one coat application every 2 years with less time and work needed. Will I save fuel with Silic One? Yes, due to easy cleaning of the surface, coating will be free from fouling and the hull will have less friction in the water. Can I go faster with Silic One? How do I know if I get enough paint on the propeller? You should apply as much paint as possible, but without sagging. Yes. You can use Hempel’s Silicone Remover available in 5l cans....

Painted with Hempel’s Silic One Aluminium Power boat, Finland Sailing boat, Netherlands AWNiemeyer, Germany Aronet, Finland

General Application Advice • Please read and carefully follow all the instructions before painting. • New gelcoats need to be epoxy primed to a minimum of 300 micron dry film thickness. • Remember to check the shelf life before use. • Painting should be avoided if there is a risk of rain! • The paint is sensitive to humidity, therefore only open the tin just before use. • Hempel’s Silic One Tiecoat and Silic One can be used up to 1 hour after opening the tin. A tin that has been opened cannot be stored for later use. • It is strongly advised to apply the maximum film thickness without sagging...

Silic One system Our most efficient antifouling solution As a world-leading supplier of trusted coating solutions, Hempel is a global company with strong values, working with customers in the protective, marine, decorative, container and yacht industries. Hempel factories, R&D centres and stock points are established in every region. Across the globe, Hempel’s coatings protect surfaces, structures and equipment. They extend asset lifetimes, reduce maintenance costs and make homes and workplaces safer and more colourful. Hempel was founded in Copenhagen, Denmark in 1915. It is proudly owned by...