Catalog excerpts
SE 84LV LOW TEMPERATURE CURE EPOXY PREPREG ¬ Versatile, high-strength prepreg system Can be processed with vacuum-only processing Excellent tack Low Viscosity – Ideal for use with heavy fibre weights Germanischer Lloyd Certified Lloyd’s Register Certified INTRODUCTION SE 84LV is an exceptionally versatile hot-melt, epoxy prepreg. It can be cured at temperature as low as 80°C (176°F), or can be used for faster moulding of components at 120°C (248°F). This is achieved with an extremely good outlife of up to 8 weeks at 18-22°C (64-72°F). It is a toughened system, and offers excellent mechanical properties on a wide variety of reinforcing fabrics and fibres. SE 84LV is commonly used in vacuum bagging, press-moulding, autoclave and other pressure moulding processes. SE 84LV is a very low viscosity system used with heavy fibre weights where low-flow processing conditions (vacuum bag pressure and minimum cure temperature), are likely to be used. With its high compressive strength it is widely used in large heavily loaded components, such as yacht hulls, and spars. It has been selected for use by various America’s Cup syndicates and boats racing in the Volvo Ocean Race. SE 84LV is widely used in sandwich structures with honeycomb, foam and balsa cores, primarily with the toughened SA 80 Adhesive Film.
Open the catalog to page 1PROCESSING NOTES - GENERAL PROCESSING NOTES - CURING CURE CYCLES When preparing the lay-up the prepreg should be removed from the freezer and allowed to thaw in a sealed bag. This may take 6 to 24 hours depending on roll size. This prevents atmospheric moisture from condensing on the prepreg which may cause voiding on cure. The mould surface should be release coated and must have been tested for vacuum integrity prior to lay-up. For a good balance of composite properties, it is recommended that the laminate is cured at 80°C (176°F) for a minimum of 12 hours. A laminate may be cured in two...
Open the catalog to page 2PRODUCT INFORMATION AVAILABILITY SE 84LV prepregs are available in a wide variety of fabric forms and collimated unidirectional tapes. Unidirectional materials are normally supplied on a single release paper and fabrics on a single polythene film. Please contact Customer Support to discuss specific requirements and availability. The product formats listed below also benefit from 3rd Party Certification. PRODUCT DESCRIPTION PRODUCT DESCRIPTION Lloyd’s Register Lloyd’s Register Lloyd’s Register Germanischer Lloyd Lloyd’s Register Unidirectional Epoxy Prepreg 150g/m2, 200g/m2 300g/m2, 450g/m2...
Open the catalog to page 3LAMINATE PROPERTIES CURED RESIN PROPERTIES Oven cured using standard processing techniques and a minimum cure time of 12 hours at 80°C (176°F). PROPERTY TEST STANDARD Tensile Strength Tensile Modulus Flexural Strength Flexural Modulus Compressive Strength UNIDIRECTIONAL LAMINATE PROPERTIES Cured using standard vacuum bag processing techniques and a minimum cure time of 12hrs at 80°C (176°F). PROPERTY Fibre Density Fibre Modulus Fibre Strength Resin Content Glass Transition Temperature 0° Tensile Cured Fibre Volume* 0° Tensile Strength (Normalised to 60%) 0° Tensile Modulus (Normalised to...
Open the catalog to page 4WOVEN LAMINATE PROPERTIES Cured using recommended processing and curing techniques. PROPERTY Resin Content Cure Method Cure Schedule TEST STANDARD Glass Transition Temperature 0° Tensile Cured Fibre Volume* 0° Tensile Strength (Normalised to 60%) 0° Tensile Modulus (Normalised to 60%) 90° Tensile Cured Fibre Volume* 90° Tensile Strength (Normalised to 60%) 90° Tensile Modulus (Normalised to 60%) 0° Comp. Str. Fibre Volume * 0° Comp. Mod. Fibre Volume * 90° Comp Str. Fibre Volume 90° Comp. Mod. Fibre Volume* SACMA SRM1-94 ASTM D 3171 Method II 0° Flexural Cured Fibre Volume* 0° ILSS Fibre...
Open the catalog to page 5NOTICE All advice, instruction or recommendation is given in good faith but the Company only warrants that advice in writing is given with reasonable skill and care. No further duty or responsibility is accepted by the Company. All advice is given subject to the terms and conditions of sale (the Conditions) which are available on request from the Company or may be viewed at the Company’s Website: www.gurit.com/terms-and-conditions.aspx. The Company strongly recommends that Customers make test panels and conduct appropriate testing of any goods or materials supplied by the Company to ensure...
Open the catalog to page 6All Gurit catalogs and brochures
-
GURIT® BALSAFLEX™
4 Pages
-
CORECELL™ S
3 Pages
-
CORECELL™ T
3 Pages
-
GURIT® PVC
3 Pages
-
CORECELL™ A
3 Pages
-
SPABOND™ 345
7 Pages
-
SPABOND™ 730
4 Pages
-
Formulated Products Brochure
23 Pages
-
T-Prime 160
8 Pages
-
T-Prime 130-1 (v5)
8 Pages
-
SMARTCURE™ (v9)
4 Pages
-
System SPRINT™ Resin (v2)
4 Pages
-
T-Lam 130-1 Slow
6 Pages
-
T-Gel 130-1
6 Pages
-
T-Paste 70-2
6 Pages
-
CR 3400
5 Pages
-
Gurit® Kerdyn® Green
4 Pages
-
Marine Market Summary (v1)
2 Pages
-
Hetairos_Gurit_Project
2 Pages
-
Aerospace
2 Pages
-
PB1000
4 Pages
-
HI-PANEL
2 Pages
-
Gurit G-PET
1 Pages
-
GURIT PRODUCT CATALOGUE 2016
88 Pages
-
Eposeal 300
6 Pages
-
Ampreg 26
8 Pages
-
Ampreg 21FR
6 Pages
-
ST 95
6 Pages
-
PREPREGS
11 Pages
-
Hi-Panel Product Brochure
2 Pages
-
CORE MATERIALS
9 Pages
-
ADHESIVES
5 Pages
-
WE91 - 2
4 Pages
-
WE91 - 1
4 Pages
-
SE 85 GT
5 Pages
-
SE 85
5 Pages
-
SE 84 Nano
5 Pages
-
PH 840
4 Pages
-
PN 901
4 Pages
-
SE 300
4 Pages
-
SC 110
4 Pages
-
SE 200
5 Pages
-
ST 16
4 Pages
-
ST 70
6 Pages
-
SE 70
5 Pages
-
SPABOND 340LV HT
6 Pages
-
SPABOND 345
4 Pages
-
SPABOND 340
7 Pages
-
SPABOND 340LV
6 Pages