TO26
2Pages

{{requestButtons}}

Catalog excerpts

TO26 - 1

DATA SHEET CURATIVE AND PREVENTIVE OSMOSIS TREATMENT TO26 Dual component, thick epoxy resin containing no solvent, for watertight polyester hulls. CHARACTERISTICS This dual component epoxy resin, containing no solvent, for thick application, is recommended for total protection of boats affected by osmosis (600 microns dry) or as a preventive treatment for polyester (400 microns). It offers excellent resistance to water. PREPARATION OF THE SURFACE Curative treatment: This treatment can only be applied to a perfectly dry boat (check with humidity tester). Remove the gel coat completely and the layers of material damaged by osmosis by sanding or planing them down. Rinse with fresh water and leave the boat to dry in order to eliminate any humidity from the hull. Check the amount of humidity with a humidity tester. When the boat is dry, apply the treatment. Preventive treatment: De-wax – remove grease carefully from the new gel coat with the de-waxer DCR900. Then sand the surface of the gel coat lightly (to dull the surface). PREPARATION OF THE PAINT Thoroughly mix the product after having added the two components. For greater precision, mixing by weight is recommended. This product must not be diluted; it contains no solvent. Ratio of the mixture by volume Compound A: 61 Compound B: 39 Ratio of the mixture by weight Compound A: 65 Compound B: 35 APPLICATION Curative treatment: Apply a coat of epoxy resin TO26 with a brush making sure the resin penetrates all the holes and imperfections in order to wet the fibres thoroughly. Leave to dry for 24 hours. Apply putty if necessary. Apply three 200-micron coats of resin TO26 with a roller, leaving 24 hours between each coat, i.e. 600 microns. Leave to dry for 24 hours then apply the primer PR20, then the antifouling. If the last layer remains sticky, rinse with a damp sponge. CHARACTERISTICS OF THE POLYMERISED RESIN Resistance to water: Excellent performance in salt and fresh water. Resistance to abrasion: Excellent. SOROMAP PEINTURE VERNIS ZA de Beligon – 1 Rue Maurice Mallet 17300 ROCHEFORT S/MER Tél : 05 46 88 36 13 • Fax : 05 46 88 36 25 • Email : william.thomas@soroma

Open the catalog to page 1
TO26 - 2

PRECAUTIONS FOR USE Wear gloves, goggles, a solvent breathing mask and protective clothing. During application and drying time there must be sufficient ventilation. HEALTH AND SAFETY See data sheet This information corresponds to the actual state of our knowledge and has the sole object of informing you about our products and possible applications. It is objectively given but does not imply any guarantee by us. Our company may modify all these details at any time SOROMAP PEINTURE VERNIS ZA de Beligon – 1 Rue Maurice Mallet 17300 ROCHEFORT S/MER Tél : 05 46 88 36 13 • Fax : 05 46 88 36 25 •...

Open the catalog to page 2

All GROUPE SOROMAP catalogs and brochures

  1. SC20

    2 Pages

  2. PR20

    2 Pages

  3. AC10

    1 Pages

  4. AC20

    1 Pages

  5. SL2

    2 Pages

  6. V2

    2 Pages

  7. AFC+

    2 Pages

  8. AF2 Racing

    2 Pages

  9. NAUTI PU

    1 Pages

  10. THICK PRIMER

    1 Pages

  11. SO184

    1 Pages

  12. STRAT SO175

    1 Pages

  13. MONOMOUSS

    1 Pages

  14. POLYMOUSS

    1 Pages

  15. POLISH PLEXI

    1 Pages

  16. PASSIVNET

    1 Pages

  17. Soromap 2017

    292 Pages