CABLEMASTER™ ACCESSORIES Accessories to aid in the installation of your Cablemaster™

CABLEMASTER™ Components Cablemaster™ Components Hawse Pipe Assembly - the stainless steel Hawse pipe assembly performs two functions: 1) it provides a watertight (IP67) barrier when the cable is fully retracted, and 2) it stores the shore power cable plug. Power Unit - the Power Unit provides the force necessary to extend or retract the cable. The Power Unit includes the drive motor, reduction gearing, guide roller assemblies, limit switches and relay assembly. Cable Storage Space - the Cable Storage Space may be built into the area below the Power Unit or a 'cable storage container' can be supplied...

CABLEMASTER™ Installation Tips General Considerations • Cablemaster power unit should be mounted directly above the storage container. • Ensure storage container is large enough to store cable easily (increase height of container rather than diameter for better results). • Vertical PVC pipe extensions to storage container should be straight (no bends). • When using PVC pipe, use pipe rollers every 18-24" (40-60 cm) to eliminate friction. • Use Glendinning 'Angling Assemblies' (not Pipe Elbows) for all complex routings and all applications 50amps and over. • Coil Guides should only be used where...

HORIZONTAL EXTENSION KIT (Part Number: 04043) The Horizontal Extension Kit is used when there is insufficient storage space immediately below the Hawse Pipe. This accessory allows the Power Unit to be installed away from the Hawse Pipe Assembly. The Vertical Extension Kit is recommended when the vertical distance between the Power Unit and the top of the storage space (or container) is too great. Using this kit helps prevent the power cable from spilling out of the storage space.

COIL SPRING EXTENSION KIT (Part Number: 04075) The Coil Spring Extension allows the installer to direct the power cable around obstructions. The Coil Spring Extension may be installed in a horizontal arrangement (pictured). Cablemaster™ Hawse Pipe Assembly Coil Spring Extension Kit Inlcudes: Item Cablemaster™ Power Unit Note: Maximum recommended length 36". Coil Spring Extension available for 16/30/32 amp & 50/63 amp applications only. Description (1) Coil Spring Extension Assembly Includes: (2) 50423 Brackets (1) 50005 Connector Link ANGLING ASSEMBLIES (Part Number: 04062 - 04067) Angling Assemblies...

PIPE END ROLLER ASSEMBLY • this keeps the cable from chaffing on the end of the PVC pipe and is highly recommended. • it is glued into the end of 3" schd 40 PVC pipe. Material: PVC Tubing, Nylon Rollers, Stainless Steel Pins STRAIGHT PIPE ROLLER ASSEMBLY • used on long pipe runs over 6' to break friction between cable and PVC pipe. • fits 3" schd 40 PVC Pipe. • Recommended to be placed at least every 2' (60cm) on long pipe runs. Material: PVC Tubing, Nylon Rollers, Stainless Steel Pins 4" (diameter) x 3.25" (D) GUIDE ROLLER ASSEMBLY (less switches) • used to replace the existing Guide Roller...

COIL SPRING GUIDE ASSEMBLY 04075-30-XX 04075-50-XX 30/32 amp Coil Spring 50/63 amp Coil Spring • Used when compound bends are required in tight areas • Installed between Power Unit and Hawse pipe. • Available in lengths 18", 24", 30", 36" (46, 61, 76, 91cm). NOTE: Do not use coil spring between Power Unit and Storage area. NOTE: Coil Guide must be straight both where the cable leaves the Power Unit and enters the Hawse pipe. Cable will bind if Coil Guide is off center at these locations. NOTE: Do not use Coil Spring Assembly for any applications larger than 63 amps. (XX = length in inches) PIPE...

GUIDE ROLLER OFFSET PLATE • used to attach the Out-Limit Switch Assembly to the Power Unit. • one comes with each Cablemaster. Material: Anodized Aluminum 3" (H) x 3.75" (D) Low profile connector link LOW PROFILE BRACKET ASSEMBLY • used to lower the height required to mount the Cablemaster from 12.5" to 10". • motor wire leads are to be reversed when using this assembly. NOTE: Low Profile Roller Kit maybe required (part number WP090). Inquire for more details. Material: Anodized Cast Aluminum Hawse Pipe Low profile guide roller bracket PIPE ELBOW with ROLLERS - 22.5° PIPE ELBOW with ROLLERS -...

POWER UNIT TO CONTAINER MOUNTING BRACKET - 17" HIGH • used to mount Power Unit to the container for easy Cablemaster installation. Mounting bracket can be attached to all containers we sell. POWER UNIT TO CONTAINER MOUNTING BRACKET - 12" HIGH • same as above bracket but 12" high. NOTE: Low Profile Assembly will be required for proper Installation when using 12"high bracket. NOTE: 12" and 17" container mounting brackets only used for CM-4 and CM-7 applications. Material: Anodized Aluminum BEZEL • used when the Hawse Pipe Cap and Hinge should not protrude from the side of the boat. Material: Anodized...

SHORE POWER CABLE (in bulk) 30 amp 125 volt - Yellow Jacket #10/3 30 amp 125 volt - White Jacket #10/3 50amp 125 volt - Yellow Jacket #6/3 50 amp 125 volt - White Jacket #6/3 50 amp 125/250 Iso Trans - White Jacket #6/3 50 amp 125/250 volt - Yellow Jacket #6/4 50 amp 125/250 volt - White Jacket #6/4 100 amp 3 ph Iso Trans - Yellow Jacket #2/3 100 amp 3 ph Iso Trans - White Jacket #2/3 100 amp 1 ph - Yellow Jacket #2/4 100 amp 1 ph - White Jacket #2/4 100 amp 3 ph Iso Trans - Yellow Jacket #2/4 100 amp 3 ph Iso Trans - White Jacket #2/4 100 amp 3 ph - Yellow Jacket #2/5 100 amp 3 ph - White Jacket...

Other Cablemaster™ Products CABLEMASTER CM - CABLE HANDLING SOLUTIONS With powered extension, retraction and storage below deck, no limit to cable length and models available to handle cable up to 250amp (or more) - there’s a Cablemaster to suit most applications. Robust marine construction and powerful drive motors (12 or 24v DC) ensure reliable service together with innovative installation options allowing cable storage in areas below deck that otherwise would go unused making the Glendinning Cablemaster the choice of many major boat builders worldwide. EASY OPERATION - with the simple flip...