TECHNICAL DATA SHEET FIX190 - (MSP190) Revision: 01/2011 Technical Data: Base Consistency Curing system Skin Formation(*) Cure Rate (*) Hardness Change In Volume Specific Gravity Maximum Deformation Temperature Resistance (cured) Elastic Modulus 100% Tensile Strength Elongation At Break Shear Strength: (*) Values may vary depending on environmental conditions Product: Fix190 is a high quality single component joint ahdesive sealant based on MS-Polymer®. It is chemically neutral and fully elastic. For use in low movement joints and for strctural bonding and direct glazing in marine, transport, aerospace and construction industries, where a strong flexible bond is required. Suitable for below waterline application. Fix190 is approved by: Det Norske Veritas (DNV) – Structural bonding and direct glazing Germanischer Lloyd (GL) - Structural bonding and direct glazing Standards Assurance Innovations – AS/NZ4020 for potable water. Characteristics: - Outstanding bond strength on most all substrates, Colour stable and UV resistant - Excellent adhesion on porous and nonporous substrates (primer may be required) - High performance mechanical properties - Flexible elastic rubber, movement accomodation ± 20% - Easy application - No bubble formulation within the sealant Page 1 of 2 MS Polymer® Stable Paste Moisture Cure Apporx. 45 min (23°C & 75% R.H) 2-3mm/24Hrs (23°C & 75% R.H) 45±5 Shore A < 2% 1.38g/mL 20% -40°C to +100°C 1.0N/mm2 (ISO 8839) > 1.6N/mm2 (ISO 8839) = 3.6MPa (ISO 37) 230% (ASTM D 1002) > 1.57N/ mm2 (ASTM D 1002) Characteristics continued: - Ecological advantages; free from isocyanates, solvents, halogens and acids - Verified by NOHSC as non-hazardous - Can be painted (compatibility tests recommended) Applications: Structural bonding and direct glazing with high end strength and flexibility. Structural bonding in areas subject to vibration. Suitable for al marine applications including glazing, bonding and sealing of floors, walls and components. Elastic bonding of components made from carbon fibre, fibre glass, aluminium, steel, copper, brass, stainless steel, glass, PVC and ABS plastics, polystyrene and timber (primer may be required) Packaging: Colour - Black and White Packaging – 290mL cartridge, 600mL foil bag Shelf life: 15 months Cartridges; 12 months Foil Bags In unopened packaging in a cool and dry storage place a t temperatures between +5°C and +25°. Note: The contents contained in this documentation are the result of our experiments and our experienceand have been submitted in good faith. Because of the diversity of the materials and substrates and the real number of possible applications which are out of our control we cannot accept any responsibility for the results obtained. In every case it is recommended to carry out preliminary experiments and compatibility tests. Fixtech Pty Ltd. PO Box 568, Southport, Qld 4215. Tel: +61 (0)7 5530 1099. Fax: +61 (0)7 5530 1322 Email: [email protected] Web: www.fixtech.com.au

TECHNICAL DATA SHEET Surfaces: State of Surface: Abraded, clean, dry, free of dust and grease Priming: For porous substrates Primer PR10 may be applied. Polypropylene Primer PR20. Nonporous substrates may be cleaned with Methylated Spirits , alcohol cleaner or wax and grease remover. We recommend a preliminary compatibility test. Joint Dimensions: Minimal Width: Maximum Width: Minimum Depth: Recommendation: 2mm (bonding) 5mm (joint) 10mm (bonding) 30mm (joint) 5mm(joint) width of joint = 2 x depth Resistance to Chemicals: Good resistance to water, aliphatic solvents, mineral oils, grease, diluted...