/^FiveAluminium Boat & Engineering Pte Ltd No.61,Tuas Ave 1, Singapore 639506 Tel: 6862 8233 Fax: 6861 0733 Email: [email protected] MINI-TUG CABIN PRINCIPLE DIMENSIONS BEAM OVERALL GEARBOX RATIO PROPELLER TYPE FUEL TANK CAPACITY MATERIAL HULL THICKNESS SIDE THICKNESS DECK BOLLARD PULL 1.2m (GUNWHALE HT AT MIDSHIP TO KEEL) APPROX 0.6M UNLADEN APPROX 4500KG UNLADEN SINGLE ISUZU 281HP@2700rpm) MARINE DIESEL ENGINE (MODEL: UM6BG1TCX) AS REQUIRED (SUBJECT TO AVAILABILITY) 4 BLADED NIBRAL (SUBJECT TO CHANGE) BUILT IN 400 LITRES FUEL TANK UNDERFLOOR MARINE GRADE ALUMINIUM ALLOY(5083H321) ALUMINIUM ALLOY CHECKER PLATE, 4MM THK APPROX 2 TONS STANDARD CONFIGURATION 1) MULTIPLE CHAMBERS CONSTRUCTION, POLYSTYRENE FOAM BLOCK FILLED 2) MARINE GRADE ALUMINIUM ALLOY CONSTRUCTION 3) MULTIPLE TRANSVERSE & LONGITUDINAL FRAME REINFORCEMENT STRUCTURES UNDER DECK 4) FULLY TIG WELDED KEEL AND CHINES WITH ADDITIONAL REINFORCED KEEL AND CHINES USING RIGHT ANGLE SECTION AS INDICATED IN DRAWING. 5) ALUMINIUM ALLOY CHECKER PLATE DECK - FULLY WELDED TO HULL SIDE PLATE. 6) SELF DRAINING COCKPIT WITH TWIN DRAINAGE HOLE TOWARDS STERN 7) FOUR (4) NOS ALLOY CLEATS 8) 100MM WIDTH ALUMINIUM ALLOY GUNWHALE SECTION (SEE DRAWING) 9) 500 LITRES ALUMINIUM ALLOY FUEL TANK WITH BAFFLES AND PRESSURE TESTED AND BOLTED DOWN IN UNDERFLOOR CHAMBER 10) FORWARD BOW PLATFORM ABOUT 1 METRE LENGTH WITH CENTRE BOARDING RAILS USING 1 %” DIAMETER ALLOY TUBING FULLY WELDED TO DECK 11) SIDE HOLDING HANDRAILS USING 1 %” DIAMETER ALLOY TUBING FULLY WELDED TO GUNWHALE

12) FORWARD 3 SIDED WHEELHOUSE WITH STEERING CONSOLE WITH HYDRAULIC STEERING SYSTEM AND CONNNECTED TO RUDDER. 13) HARDENED WINSHIELD WITH ALUMINIUM FRAME 14) SINGLE CLEARVIEW CIRCULAR WINDSHIELD WIPER ON DRIVER SIDE WINDSHIELD 15) 1 NOS CUSHION TYPE SEATING FOR COXWAIN AT DRIVING CONSOLE 16) BOAT IS PAINTED WITH JOTUN MARINE PU PAINT SYSTEM 17) ANCHOR LOCKER AND HATCH UNDER BOW PLATFORM 18) 4 NOS LIFTING EYE WELDED ONTO DECK AND FRAME AT FLOOR LEVEL 19) REAR TOWING POST WITH STRUT SUPPORT 20) AL ALLOY PROPELLER RING AS INDICATED IN DRAWING 21) ALUMINIUM ENGINE ROOM BOX COVER WITH VENTILATION...

7) 1 NO. BATTERY ON-OFF SWITCH 8) 1 NO. FUEL EMERGENCY SHUT OFF COCK WITH FUEL HOSE 9) 1 NOS. 1200GPH RULE BILGE PUMP WITH AUTOMATIC FLOAT SWITCH 10) STAINLESS STEEL RUDDER WITH RUDDER STOCK AND PACKING GLAND QUALITY CONTROL TEST 1) 24 HOUR WATER LEAK TESTING ON HULL AT PRODUCTION STAGE. - UPON OVER-TURNING OF HULL BOTTOM, THE HULL SHALL BE FILLED WITH WATER AND LEFT STANDING OVERNIGHT FOR 8 HRS. - VISUAL INSPECTION TO BE CARRIED OUT AT ALL WELDED JOINTS BELOW WATER LEVEL FOR SIGNS OF WATER LEAK - DRAIN WATER AND DRY HULL AFTER TEST. 2) ENGINE STARTING AT OUR FACTORY BEFORE DELIVERY TO OWNER'S...

Comfortable and Well Designed Helmstation ISUZU 281hp Marine Inboard Engine

Fold-Down Bench Seatings