- Catalogs
- ES Manufacturing
- G9609l2.5
G9609l2.5
G9609l2.5
- Type of Feed: Suction
- Air Inlet: 1/4”
- Nozzle Diameter: Standard 2.5mm, Optional 1.5-2.3mm
- Recommended Air Pressure: 3.0-4.0 bar (45-60 psi)
- Max Air Pressure: 8.3 bar (120 psi)
- Paint Capacity: 1000cc
- Average Air Consumption: 170-250 l/min (6.0-8.8 cfm)
- Pattern Width: 180-230mm (7.1-9.1”)
- Weight: 1.1 kg (2.42 lbs)
- Sound Pressure Level: 77.1 dB(A)
- Sound Power Level: 90.1 dB(A)
- Wear safety gear to prevent exposure to toxic vapors.
- Do not use oxygen or combustible gases as a power source.
- Operate in well-ventilated areas away from ignition sources.
- Disconnect from air supply during maintenance.
- Use clean, dry air and do not exceed maximum pressure.
- Avoid using incompatible solvents with aluminum and zinc parts.
- Ensure all components are securely tightened before use.
- Inspect the product for damage before use.
- Mix and strain materials as per manufacturer’s instructions.
- Fill the canister ¾ full and connect to the air supply.
- Adjust spray pattern using the pattern and material adjusting knobs.
- Maintain a consistent distance and angle while spraying.
- Clean thoroughly after use to prevent function failures.
- Disassemble and clean all components with solvent.
- Reassemble and test with a small amount of solvent.
- Store with fluid adjustment knob open to reduce tension.
- Fluttering or spitting: Check material level, connections, and clean components.
- Pattern issues: Adjust material viscosity and air pressure.
- Air leaks: Lubricate or replace faulty components.
- Fluid leaks: Tighten or replace packing nut and lubricate.
- Excessive overspray: Adjust pressure and distance.
- Will not spray: Check air lines and fluid control.
Catalog excerpts
HIGH PRESSURE SPRA Y GUN G960-1L-2.5 Read this Instruction Manual carefully and understand it completely, basic precaution should be strictly followed to prevent the damage to the tool and injury to the operator. Retain this manual for further reference. CONTAIN: ♦ Description ♦ Specification and Technical Data ♦ Important Safety Instruction ♦ Instructions for Operation ♦ Maintenance/Storing ♦ Troubleshooting/Repairs ♦ Parts List PDF processed with CutePDF evaluation edition www.CutePDF.com
Open the catalog to page 1
Engineered Solutions Ursmbuted Makers of fine too s and accessories for the fiberglass and composite mdustnes 2647 24th Street North, Saint Petersburg, Florida USA Description A high pressure spray gun is ideal for refinishing a boats or a wide variety of gel coat repair projects. This high pressure material sprayer features air fluid and fan controls to offer a wide variety of patterns. It is supplied with a 1000 cc suction feed aluminum cup. Pattern Adj.Knob Fluid Adj.Knob
Open the catalog to page 2
Important Safety Instructions 1. For toxic vapors produced by spraying certain materials can create intoxication and serious damage to health. Always wear safety glasses, gloves and respirator to prevent the toxic vapor hazard, solvent and pointing paint coming into contact your eyes or skin. (see fig 1) 2. Never use oxygen, combustible or any other bottle gas as a power source or would cause explosion and serious personal injury. (see fig 2) 3. Fluid and solvent can be highly flammable or combustible. Pls Use the tool only in well-ventilated area, and avoid any ignition sources, such as smoking,...
Open the catalog to page 3
Engineered Solutions Ursmbuted Makers of fine too s and accessories for thefiberglass and composite mdustnes 2647 24th Street North, Saint Petersburg, Florida USA The desired pattern, volume of fluid output and fine atomization can easily be obtained by regulating the Pattern Adjusting Knob, Fluid (MATERIAL) Adjusting Knob PATTERN ADJUSTMENT: Turning Pattern Adjusting Knob to the right until tight will make spray pattern round, or turning left make spray pattern ellipse. Fluid (MATERIAL) ADJUSTMENT: Turn the Material Adjusting Knob clockwise will decrease the volume of fluid output and counter-clockwise...
Open the catalog to page 4
Engineered Solutions Ursmbuted Makers of fine too s and accessories for thefiberglass and composite mdustnes 2647 24th Street North, Saint Petersburg, Florida USA Incomplete cleaning could cause function failures and a degradation of the fan form. 1. Remove any remaining material by pouring it into another container. 2. Disassemble the spray gun making sure to remove the needle before disassembling the nozzle to avoid damage to the housing of the nozzle closure. 3. Clean all the material passages and the nozzle. Clean the other components using a brush soaked in solvent. 4. Clean all overspray...
Open the catalog to page 5
Engineered Solutions Ursmbuted Makers of fine too s and accessories for thefiberglass and composite mdustnes 2647 24th Street North, Saint Petersburg, Florida USA
Open the catalog to page 6
G960 Spray Gun Parts Diagram NK Nozzle Note 1: G960-005 is set with thread locking material and can be difficult to remove. Use a 6 point hardened socket only! Note 2: G960-020 “O” Ring may not be included at the factory, but 2 are supplied by in seal kit & recommended by ES Mfg. ES Manufacturing, Incorporated Distributed Worldwide Engineered Solutions Manufacturers & Suppliers of fine tools and accessories for the fiberglass and composite industries 2647 24th Street North, Saint Petersburg, Florida USA G960001- Air Inlet Coupling G960002- Air Inlet /Inlet Body“O” Ring (2Pc) G960003- Hex Socket...
Open the catalog to page 7
Model G960 Resin/Gelcoat Spray Gun Documentation & Warranty Packet/Documentación y Paquete de Garantía Thank you for purchasing G960 Spray Gun. If properly maintained, this sprayer will provide years of trouble free service. Gracias por comprar la Pistola de Copa más favorita en el mundo. Si se mantiene apropiadamente, “ESTA” le proveerá muchos anos de servicio sin problemas. WARRANTY/GARANTIA This model G960 Spray Gun is warranted against defects for a period of 60 days. Keep your original sales receipt for proof of purchase. ES Manufacturing, Inc. will replace or repair any defective part,...
Open the catalog to page 8All ES Manufacturing catalogs and brochures
2023 Catalog65 Pages
G860 2.51 Page
G10061 Page
G20061 Page
G6604.51 Page
G8302.01 Page
G9601l2.58 Pages
G9602l2.58 Pages
MB1101 Page
MB601 Page
MB501 Page
MXB0751 Page
VS7501 Page
VS12001 Page
XB-0751 Page
XB-2001 Page
Mini Rollers1 Page
Segmented Rollers1 Page
Tape Rollers1 Page
Catalog60 Pages