Catalogs >
Eaton >
Newport harbour mate specifications

Newport harbour mate specifications
2Pages

Catalog excerpts

Eaton Electrical ine General Specifications 1000 Cherr ngton Parkway fof fhe Newport Harbor United States Mate Pagel www.EatonElectrical.com All Power Pedestals Must Meet the Following: A. Shall be tested and certified to be in compliance with ANSI/UL® 231 entitled "power outlets." B. If a laboratory other than UL is used, that laboratory must certify, in writing, that the power outlet has been tested and meets all of the requirements of ANSI/UL 231, including 746C polymeric materials, and that the unit will pass the 94VO-5V flame test. C. Shall be certified to meet all sections of NFPA® 303, Fire Protection Standards for Marinas and Boatyards - 2006 Edition. D. Shall meet 406.8 (B)(2)(a) of the National Electrical Code® NFPA 70, i.e., "A receptacle installed in a wet location shall be installed in a weatherproof enclosure, the integrity of which is not affected when the attachment plug cap is inserted." E. The receptacles shall be mounted at a down angle of 35 degrees or greater from vertical to relieve the strain of the cable weight on the receptacle locking mechanism. 2.1 Acceptable Manufacturers — Power Pedestals/Newport Harbor Mate Enclosures Marina Power and Lighting 2.2 Power Pedestals/Newport Harbor Mate Enclosures — 1. The housing shall be constructed of 1/4" thick injection molded resin material and shall be coated with a UV-resistant polyurethane. It shall be UL listed as a type 3R weatherproof 1. The power pedestal shall be completely pre-wired at the factory to the load side of compression lug assembly. 2. All load copper wiring shall be of high stranding and tin-plated 3. The maximum size of the line wiring shall be # 2/0 AWG direct feed or #1 loop feed without stainless steel pedestal. 4. The maximum size of the line wiring shall be 350 MCM direct feed or #4/0 AWG loop feed with stainless steel C. Loop Feed Bus Bar System: 1. If no stainless steel pedestal base is utilized, the bus system shall be a 1/4" - 20 silicon-bronze stud with a silicon-bronze Belleville type washer. The 1/4" - 20 silicon-bronze hex-nut shall be torqued to 100 inch-pounds. 2. If a stainless steel pedestal base is utilized, the bus system shall be a 3/8" - 16 silicon-bronze stud with a silicon-bronze Belleville type washer. The 3/8" - 16 silicon-bronze hex-nut shall be torqued to 200 inch-pounds. 3. Double Barrel Mechanical Lugs (Optional) — rated for copper 1. All exposed metallic parts must have integral ground that is a part of the equipment grounding system. 1. All receptacles shall be of the corrosion resistant type, con- form to NEMA® L - 5 and/or NEMA L - 6 requirements and are rated for marine use. 100 ampere receptacles should 2. All receptacles shall be mounted at an angle that is minimum 35 degrees from vertical and located behind a lockable weatherproof-hinged door that is under tension to ensure proper closing pressure when receptacle is or not in use. 3. All receptacles shall be mounted at least 24" above the dock. 1. All breakers for receptacles shall be of the thermal-magnetic type, 10,000 AIC, and shall be UL listed. 2. Circuit breakers for the receptacles shall be covered with the same lockable door that covers the receptacles.

Open the catalog to page 1

Eaton Electrical ine General Specifications 1000 Cher ngton Parkway f fh Newport Harbor United States Mate 1. The base shall be stainless steel and bolted to the Harbor 1. Receptacles for boat users shall be a locking and grounding type, either single-phase, 125 volt 30 amp and/or 50 amps, 1. Each pedestal shall be equipped with non-metered light. The Ight shall be a 7 watt fluorescent biaxial light that Is controlled 2. The lighting shall not Interfere with boaters' navigation. 1. Circuit breakers for 30 amp receptacles shall be a single-pole, 125 volt, 30 amp thermo-magnetlc type. 2....

Open the catalog to page 2