426HSS Series Hexa-Sinking Switch Module Introduction The E-Plex 426HSS series has been designed to simplify electronic systems wiring by interfacing to devices that require a pull to ground signal. This multi-module is ideally suited to drive solenoid, motor, and lighting applications. It is intended to withstand harsh environments and utilizes sealed Delphi connectors for an IP66 rating. The module is designed to meet UL1500 standards for ignition proofing. Local electronic override capabilities allow independent operation of the device loads. Key Features Design Specifications • 0 amps total power capability 6 • Shock: Mil Std 202 Method 213 test condition 1 • 6 solid-state low side outputs capable to 10 amps each • ibration: Tested to Lloyds Register Approval Vibration V Test 2 • High side output withstands up to 20A inrush current • Local electronic override capabilities • tatus LED’s for each channel S • Reverse Battery Protected • Short circuit detection • LEN value 2 • ransient voltage suppression: EN6100-6-1 T • oisture resistance: IP66 M • CB characteristics: UL94V-0 P • ower distribution: UL 1077 compliant (except highP voltage dielectric test) • gnition protection: UL 1500 compliant I • alt spray: Tested to Lloyds Register Approval Salt S Spray Test • perating Temperature: -40°C to 60°C O • torage Temperature: -40°C to 85°C S • Operating Humidity: 0% to 100% (condensing) • eight: 1.34 lb (610 grams) W Powering systems - Empowering designers

426HSS Series Electrical Specifications Description Min Nominal Max Absolute Max (Surge) Voltage 7 VDC 12 / 24 VDC 32 VDC 45 VDC 2 Current, Total 0.025 A 30 A 60 A 1 160 A 2 Current, per channel continuous 0 5 10 A 30 A 5 Current, per channel intermittent duty3 0 – 15 A 30 A 5 Inrush capable per channel – – 20 A 30 A 5 Lead inductance 0 – 2 mH 6 – Load Inductance 0 – 20 mH – Output Impedance4 8 mΩ 10 mΩ 12 mΩ – NOTES: 1. De-rate max current by 0.2A per °C above ambient, 25 °C 2. Measured at 8.3ms single half sine wave. (JEDEC Method), 10,000 pulses 3. Duty cycle at 1 minute on time, 5 minutes...

426HSS Series Wiring Specifications Pin # Pin Description Pin # Pin Description A1 Solid State Output 3 A2 E-Plex Data Bus + E1 Output 3 Return E2 E-Plex Data Bus – B1 Solid State Output 1 B2 Solid State Output 6 F1 Output 2 Return F2 Output 6 Return C1 Solid State Output 1 C2 Solid State Output 5 G1 Output 1 Return G2 Output 5 Return D1 E-Plex Data Bus + D2 Solid State Output 4 H1 E-Plex Data Bus – H2 Output 4 Return M5-T1 Battery Power M5-T2 Battery Return Outputs and Returns: Analog = 0 to 15A for 7 to 32VDC | Battery Power (+): 0.025A to 16A, 7-32VDC Status LEDs: ON - Channels 1-6 indicates...

426HSS Series Pin Specifications Female Terminal Cable Range AWG (mm2) Terminal Insulation Range 18-16 (1.0-0.75 mm2) 15304716 1.70-2.25 mm 16-12 (2.50-1.50 mm2) 15304717 2.20-3.00 mm Seal Insulation Range Seal P/N 1.20-1.85 mm 15366063 1.85-2.25 mm 15356064 2.09-2.66 mm 15366061 2.70-3.2 mm 15336674 Typical Wiring Diagram E-Plex + M5 - T2 Ch. 6 A2 E-Plex – E2 Lamp Ch. 5 Motor B2 Ch. 4 C2 Status LEDs, Channels 1 - 6 and E-Plex9 Pump D2 M5 - T1 A1 E-Plex Pump B1 Ch. 3 Motor C1 Ch. 2 Ch. 1 Lamp H1 D1 E-Plex – E-Plex + Channels 1-6, Override Switches7,8 Battery Return (Ground) Fuse / Disconnect,...

426HSS Series Mounting Specifications Screw assembly to a flat mounting surface in 2 places, as shown in the illustration. Mounting Instructions Imperial (English) fasteners: Use #10 size screw, #10 split lock washer, #10 washer. Torque to 20~22 in-lb. Do not exceed this torque as it could cause damage to the electronics. Metric fasteners: Use M5 size screw, M5 split lock washer and M5 washer. Torque to 250~280 N-cm. Do not exceed this torque as it could cause damage to the electronics. Mechanical Specifications Connectors: J1 - Brown: Mates to Delphi P/N 15317308 J2 - Blue: Mates to Delphi P/N...

Powering Systems - Empowering Designers George Summers Close, Medway City Estate, Rochester, Kent ME2 4EL tel: +44 (0)1634 778704 Fax: +44 (0)1634 290773 email: [email protected] web: www.e-plex.co Important Notice: E-Plex Ltd. (E-Plex) reserves the right to make changes to or discontinue any product or service identified in this publication without notice. E-Plex advises its customers to obtain the latest version of the relevant information to verify, before placing any orders, that the information being relied upon is current. E-Plex assumes no responsibility for infringement of patents or rights...